Bucher C-LRV 175 Скачать руководство пользователя страница 79

Страница: 79 / 92

−

LRV lift control valve

Operation

79/92

300−I−9010212−E−10/08.08

5.2

Calculating the demand values for maximum speed

The demand values are shown on a label on the C−DELCON’s
microprocessor

The demand values for the maximum UP and DOWN speeds can be
calculated from the following table:

Valve type

Flow range, Q

[l/min.]

Flow ring

Conversion

C−LRV 175

15–45
46–90

91–250

R45
R90

R250

1V <=> 4.8l/min.
1V <=> 9.7l/min.

1V <=> 29.1l/min.

C−LRV 350

251–500

R500

1V <=> 52.2l/min.

C−LRV 700

400–1000

R1000

1V <=> 112.0l/min.

−

LRV 175

−

120 / 150

−

21 / 45

R 250

−

K 251 / 6

−

80 / 55 bar

Calculation example

Flow rate UP (Q)

120l/min.

Flow rate DOWN (Q)

150l/min.

Valve selection:

Valve type

C−LRV 175

Flow range

91–250l/min. *

Flow ring

R250

Conversion

1V <=> 29.1l/min. *

Conversion:

Flow rate UP:
120[l/min] / 29.1[l/min]

4.12V

Fast UP

Flow rate DOWN:
150[l/min] / 29.1[l/min]

5.15V

Fast DOWN

→

Settings in the C−DELCON

* These values are taken from the above table.

Содержание C-LRV 175





























































































Результаты поиска

Содержание C-LRV 175

Отзывы:

Похожие инструкции для C-LRV 175

Бренды по названию

Популярные бренды

Bucher C-LRV 175, Руководство по установке и запуску

Результаты поиска

Содержание C-LRV 175

Отзывы:

Похожие инструкции для C-LRV 175

Бренды по названию

Популярные бренды