![background image](http://html1.mh-extra.com/html/bticino/tvcc-391601/tvcc-391601_instructions-for-use-manual_2825232004.webp)
1
2
3
4
Connect the camera to a 230V a.c. power source.
Adjust the lens focus and the diaphragm (in case manual diaphragm lenses are used), so as to optimize the picture.
Lenses
Use CS-mount lenses. It is also possible to use C-pitch lenses with a suitable adapter.
Connect the lens connector to the IRIS terminal on the side.
Note: When using lenses with power-driven zoom in the outdoors case item No. 391803, it is necessary to fasten both the lens and the camera to
the internal supporting bracket, using the supplied spacer by screwing it to the camera body.
The camera is delivered in standard back focus position. However, for certain types of zoom lenses, an adjustment may be necessary.
Descriptions
1
Lens mount: CS mount
2
Camera fixing screws: on the wall, in the case, etc.
3
Lens back focus adjustment
4
IRIS terminal: connect when an automatic diaphragm lens is used
5
Video output connector (BNC)
6
Power cord: connect to 230V a.c. power line
7
AES (automatic electronic shutter) switch: to set the AES mode with
manual diaphragm lenses, set the switch on ON.
Set the switch on OFF when automatic diaphragm lenses are used.
8
SENS UP switch: to increase sensitivity, set this switch on ON
9
BLC switch for backlight compensation: for backlight shooting, set this
switch on ON
10 ALC level: potentiometer to adjust video output level in case automatic
diaphragm lenses are used
11 V-PHASE: potentiometer to adjust vertical synchronism for systems
with several cameras
12 AUTO IRIS switch: select VIDEO for lenses with amplifier; select DC
for lenses without amplifier.
SENS UP
BLC
AES
ON
OFF
7 8 9
ALC
LEVEL
V-PHASE
10
11
2
2
1
6
DC
VIDEO
4
3
5
12
Note: Designs and specifications are subject to changes without prior notification.
Features
Supply voltage
230V a.c.
±
10% / 50
±
1Hz
Electrical input
30mA
Sensor
CCD 1/3" black-and-white
Scanning system
2:1 interlaced
Picture element
512 (H) x 582 (V) mm
Scanning area
4.92 (H) x 3.67 (V) mm
Scanning frequency
15.625 kHz (H) / 50Hz (V)
Resolution
380 TV lines (H) / 400 TV lines (V)
Sync. system
Line Lock
Minimum illumination
0.09 lx F1.2 (with SENS UP ON)
AGC (Automatic Gain Control)
yes
Output signal
1Vpp 75
Ω
CCIR compatible
Gamma correction
0.45
Signal-to-noise ratio
≥
46dB
AES (Automatic Electronic Shutter)
1/50 - 1/50000 sec./OFF
Video output
1 BNC
Automatic diaphragm
4P connector (d.c/video)
Working temperature
10
°
C - 50
°
C
Working humidity
30% - 90%
Dimensions (W x H x D)
60 x 60 x 120mm
Weight
680 g
Warnings
- Never point the camera at the sun.
- Never point the camera at the sun even if you are not
shooting.
- Do not shoot with very intense light.
- Do not drop, hit or submit the camera to vibrations.
- Do not touch internal parts.
- Install the camera in a place where it will not get wet.
If it does get wet, immediately disconnect from power source
and contact the after-sales service.
- Install the camera away from video interference sources.
When camera cables are laid close to electric cables or TV
aerials, picture interference may result. In this case, lay the
cables again or re-install the camera.
- Check ambient temperature and humidity.
If the ambient temperature is higher or lower than the one
indicated in the specifications, picture quality may be affected
or some internal parts of the camera may fail.
The camera should not be used in these conditions.
The same applies in conditions of high humidity.
IRIS
terminal
Camera
Lens
1
3
2
4
Welding side
IRIS TERMINAL
DC position
Control
1
Control
2
Drive
3
Drive
4
(GND)
VIDEO position
9V IRIS feed
(50mA max)
0.8Vpp
Video signal
GND
GND