BTEK T419S Скачать руководство пользователя страница 21

Страница: 21 / 30

T419S Indicator User Instructions

4.1 User menu

4 Menus

The T419S three user accessible menus:

User

menu - Use to set Time, Date, Site ID, check Seal status and check

Archive information.

About

menu - Use to see information on the software, firmware, application,

serial number, options, ethernet and downloads

Audit

menu - Use this to check and/or print the calibration and configuration

counters.

The password for these menus is 111. Follow these steps to access and use these
menus.

Press and hold the

SETUP

key until …

the password entry screen appears.

Key in 111 and press the

ENTER

key …

This screen is displayed:

The bold box around the center image means that is the highlighted
menu item.

Use the

Left

and

Right

keys to highlight the menu you want to enter and press

the

ENTER

key. Below are the explanations for these menus.

4.1 User menu

When the User menu is selected, these choices appear:

Use the

Left

and

Right

keys to highlight the menu item you want to access and press

the

ENTER

key.

Time

Set

- Use the numeric keys to enter the correct time in the style chosen

below.

Style

- Choose the style of time display from these choices:

12HR - Shows time in the 12 hour style

12HR-AP - Shows time in the 12 hour style with AM/PM

24HR - Shows time in the 24 hour style

User

About

Audit

Time

Date

Site ID

Seal

Archive

Содержание T419S






























Результаты поиска

Содержание T419S

Отзывы:

Бренды по названию

Популярные бренды

BTEK T419S, Инструкция пользователя

Результаты поиска

Содержание T419S

Отзывы:

Бренды по названию

Популярные бренды