background image

HRB Service Manual

5

1.1    About this manual

1 General information and warnings

1.1 About this manual

This manual is divided into chapters by the chapter number and the large text at the top 
of a page. Subsections are labeled using the 1.1 and 1.1.1 convention. The names of 
the chapter and the next subsection level appear at the top of alternating pages of the 
manual to remind you of where you are in the manual. The manual name and page 
numbers appear at the bottom of the pages.

1.1.1 Special messages

Examples of special messages you will see in this manual are defined below. The 
heading words have specific meanings to alert you to additional information or the 
relative level of hazard.

Installations within Europe

 must use a socket which provides a minimum of IP56 

protection to the plug / cable assembly. Care must be taken to make sure that the 
degree of protection provided by the socket is suitable for the environment.

1.2 Routine maintenance

Always disconnect the interface cable from the indicator before starting any routine 
maintenance to avoid the possibility of electric shock.

CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result 
in damage to equipment or corruption to and loss of data.

NOTE: This is a Note symbol. Notes give additional and important information, hints 
and tips that help you to use your product.

IMPORTANT: This equipment must be routinely checked for proper operation 
and calibration.
Application and usage will determine the frequency of calibration required for 
safe operation.

Содержание HRB





















Отзывы: