BTECH S5 BATTERY VALIDATION SYSTEM SCM-600 Скачать руководство пользователя страница 56

Страница: 56 / 58

S5 Battery Validation System

Seeing When the Batteries Have Been Used/Discharged

Discharge readings show when your uninterruptable power supply has stopped working at full capacity. At
these times your battery system has been under load, and discharge readings were sent to the BVM.

Action

How to do it

Picture

If not already

running, start BVM,

open a *.bvm file.

a. From the Start menu, select Programs > BTECH > Battery Validation Manager 4.0

b. In the Location List window, click on a location file, then click OK. A *.bvm file will open,

showing battery measurements.

View numerical data

about each

discharge.

Click on the

Discharges

tab of the

open *.bvm file display.

A series of readings

will appear, showing

the duration of each

discharge.
Click on a reading in

the upper window to

see a related series of

voltage and impedance

readings in the lower

window. Entire system

voltage and currents are

recorded during the

initial system stage.

Individual unit voltage

and temperature

readings as well as

ambient temperature

readings are then

continuously read

afterwards.

Содержание S5 BATTERY VALIDATION SYSTEM SCM-600



























































Результаты поиска

Содержание S5 BATTERY VALIDATION SYSTEM SCM-600

Отзывы:

Бренды по названию

Популярные бренды

BTECH S5 BATTERY VALIDATION SYSTEM SCM-600, Руководство по эксплуатации

Результаты поиска

Содержание S5 BATTERY VALIDATION SYSTEM SCM-600

Отзывы:

Бренды по названию

Популярные бренды