BSS Audio DPR-901ii Скачать руководство пользователя | Manualshive

Страница: 23 / 30

background image

23

12kohm electronically balanced,
+20dBu (+20dBv) maximum input level via a 3 pin male XLR cable plug.
Common Mode rejection

> -50dB, 20Hz to 20kHz.

Electronically balanced and floating, capable of d20dBu (+20dBv)
into 600ohms or greater via an XLR female cable plug.

Frequency response

+/- 0.5dB, 20Hz to 20kHz
with all sections bypassed.

Noise

< -86dBu, all controls set flat (CCIR 468-2)

Distortion

THD < 0.05% 20Hz-20kHz at +15dBu, all
controls set flat.

Frequency

Band 1 LF

Sweepable from 40Hz to 320Hz.

Band 2 LM

Sweepable from 150Hz to 1600Hz.

Band 3 HM

Sweepable from 800Hz to 9kHz.

Band 4 HF

Sweepable from 1.6kHz to 18kHz.

Width

Variable from narrow (0.5Oct) to wide (3Oct)
Width control is inoperative in SHELF mode.

Filter Shelf

Selects shelving EQ response (Bands 1 & 4)

Filter Defeat

Selects broadband operation (Bands 2 & 3).
A bell-shaped EQ response is the norm for all
bands if these switches are ‘out’.

Threshold

Variable from +20dBu to -30dBu.

Comp/Exp

Variable from -30dB compression to +16dB
expansion. Soft knee at low settings.

Below

Switched in for below threshold processing.

Fast Release

Switched out to prevent pumping on
composite music mixes.
Switched in to respond to highly dynamic
signals.

Metering

- per channel:

8 horizontal green LEDs indicate
compression activity.
8 horizontal red LEDs indicate expansion
activity.
Note: The 1-8 scaling is for convenience
only. It is not a decibel scale.
6 vertical LEDs display signal level (in dB)
relative to the threshold control’s setting.

Band In

Switches each band into circuit.

EQ In

Enables or bypasses the whole system.

Output

Headroom indicating 4 LED display,
indicates CLIP (overload =+20dBu), +15dBu,
+10dBu, as well as signal present (-20dBu).

Appendix B

Specifications

Input Section

Output Section

Operating Controls

- Each Band

Operating Controls

- Overall

Specifications

«
...
21
22
23
24
25
...
»

Содержание DPR-901ii































Отзывы:

Нет отзывов

Похожие инструкции для DPR-901ii

Бренд: Aiwa Страницы: 24

Бренд: Bogen Страницы: 2

Бренд: Steren Страницы: 12

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 29

Бренд: Philips Страницы: 30

Бренд: Philips Страницы: 48

Бренд: Philips Страницы: 100

Бренд: Philips Страницы: 105

Бренд: Philips Страницы: 48

Бренд: Philips Страницы: 108

Бренд: Pioneer Страницы: 20

Бренд: Pioneer Страницы: 19

Бренд: Pioneer Страницы: 15

Бренд: Pioneer Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды