background image

1. Heat up the engine

2. Make sure the car battery is fully charged

3. Connect PPC

®

 to the car

4. Turn ignition on to second position

5. Turn off current consumers  

6. Press ENTER

7. Follow instructions on the display

8. Display shows ”Done, remove PPC”

9. Turn ignition off

10. Remove PPC

®

Show stored VIN

Menu function

The VIN to which PPC

®

 is married 

is displayed. Your PPC

®

 only works 

with that VIN.

Press 

MENU

 to get this 

menu function. 

Press 

ENTER

 to select 

the displayed function.

Technical specifi cation

Communication to car:................. 

CAN high

 

 

 

CAN low

 

 

 

K-line

Communication to PC:.................. 

RS232

 

 

 

USB

Power requirement:..................... 

9-16V/ DC

Energy consumption:................... 

max 500mAh

Display:...................................... 

1x16 LCD

PPC

®

:......................

Portable Program Carrier

Tune Car?

Tuning 0-100%

Read car?

Reading 0-100%

Press (ENTER)

Please wait...

Done, remove PPc

Done, remove PPc

Press 

ENTER

 to start 

programming. Duration: 20 min.

Press 

ENTER

 to start reading. 

Duration: approx 60 min.

Turn ignition off and remove PPC

®

 

from the diagnostic outlet.

The car is now successfully 

tuned!

Turn ignition off and remove PPC

®

 

from the diagnostic outlet.

PPC

®

 now contains your car’s 

original software.

This fi le can be sent to BSR via 

Internet. For more info see our 

website http://www.bsrab.se/ppc

One of the three following 

alternatives will be activated.

Return to orig?

Press 

ENTER

 to start 

programming. Duration: 20 min.

Original 0-100%

Done, remove PPc

Turn ignition off and remove PPC

®

 

from the diagnostic outlet.

The car’s original software is 

now installed.

Programming must not be 

interrupted. Do not disconnect 

OBDII cable before display 

shows DONE REMOVE PPC.

Reading must not be 

interrupted. Do not disconnect 

OBDII cable before display 

shows DONE REMOVE PPC.

Programming must not be 

interrupted. Do not disconnect 

OBDII cable before display 

shows DONE REMOVE PPC.

Instructions shown on the display

Disconnect cooling fan and low beams, then press 

Enter

. See next page!

Reconnect cooling fan and low beams, then press 

Enter

.

Manual for Saab Trionic 7

Getting started

Check that the car has been properly serviced and that no warning lamps are lit. If anything is 

wrong with the car it should fi rst be taken to a car repair shop. Reloading the software will not fi x 

a malfunctioning car.

Take the car for a testdrive and heat up the engine to normal temperature before PPC

®

 tuning. 

Make sure that the car battery is fully charged, if any doubt connect battery charger.

 

Use EU 98 octane fuel (US 93 octane).

Cell phone might cause interference. Please remove or turn it off.

Connecting PPC

®

 

to the car

Connect the supplied OBDII cable to the PPC

®

 modular port. Do not connect PPC

®

 to the car and 

PC at the same time, it can damage PPC

®

.

Connect PPC

®

 to the OBDII outlet of the car. The OBDII outlet is located under the steering wheel.

Turn ignition on, to the second position before the starter motor gets activated.

Turn off all current consumers, such as: radio, headlight, air conditioning, electric seat heater, 

window defroster, cooling fan etc. Do not activate any current consumers while programming.

 

Operating instructions

When PPC

®

 is connected to the car the status is displayed.

Press 

MENU

 button to scroll through the menu functions. 

Press 

ENTER 

button to select the displayed function.

Do not activate any electrical accessories (cell phone, radio, air conditioning etc.) while 

installing the PPC

®

 software. Do not open or close car doors.

After programming disconnect PPC

®

 from the car. PPC

®

 must not be connected to the car while 

driving!

Upgrading the PPC

®

Software upgrades can be downloaded to PPC

®

. To be able to do that you need a COM-port cable, 

USB-cable and the program PPC Update. You fi nd PPC Update on the BSR website:

http://www.bsrab.se/ppc. 

You can also read the supplied manual for PPC Update.

Storage

The PPC

®

 must not be exposed to water, moisture or condensation. Store PPC

®

 in a place free 

from dust and vibrations. Do not store PPC

®

 near strong magnetic fi elds.

Programming must not be interrupted! Do not disconnect

OBDII cable before display shows ”Done, remove PPC”.

Отзывы: