background image

BOB’S SPACE RACERS

®

                                                                                                                    BONGO BEAT

TM

 ARCADE MANUAL BSR V3.0 

19 

 

Symptom Possible 

Problem 

Solution 

 

             POWER 

POWER 

Sound Problems 

   -No sound 
   -Low Sound 
   -Intermittent Sound

 

Low Volume 

Check Volume Control and adjust as necessary 

Faulty speaker harnessing 

Check connections and/or repair harnessing 

Faulty speaker 

Check and/or replace speaker 

Faulty sound board or sound board harnessing 

Check connections or Replace Sound Board 

Faulty Main P.C. Board 

Check and/or repair or replace Main P.C. Board 

 
Game does not take or add 
money correctly 

Coin switch out of adjustment 

Re-bend coin switch wire 

Coin mech dirty or improperly adjusted 

Clean and adjust mech as necessary 

Faulty Coin switch 

Check and/or replace switch 

Faulty coin switch harness or connector 

Check and/or repair harnessing 

Game improperly programmed 

Check programming options and adjust 

Faulty Main P.C. Board or component 

Repair and/or replace Main P.C. board 

 
E1 displayed on LED 
Ticket Dispenser not 
working properly, or no 
tickets being dispensed 
 

No tickets in the game 

Refill ticket dispenser 

Tickets jammed in dispenser 

Clear ticket jam 

Ticket dispenser sensor blocked with debris 

Clean off sensor 

Poor connection on the ticket dispenser 

Check and/or replace connectors 

Game improperly programmed 

Check ticket programming options 

Faulty ticket dispenser 

Replace dispenser 

Faulty ticket dispenser harnessing 

Check and/or repair harnessing 

Faulty Main P.C. Board 

Replace or repair Main P.C. Board 

 
Game will not start. 

Game power off 

Check on/off switch and power cord  

Main fuse blown 

Check and/or replace fuse as necessary 

Power Supply problem or failure 

Check Power Supply output and connections 

Faulty P.C. board or component 

Repair and/or replace main P.C. board 

 
Game stops or is stopped 
with nothing displayed 

The power connector is disconnected. 

Reconnect the connector securely. 

Possible faulty connection or short circuit. 

Check all circuitry for faulty connections or short 
circuits. 

 
Toys will not move 

Mechanical Interference 

Remove Interference 

Chain is broken 

Repair Chain 

Faulty Home / Win switch 

Replace Switch 

Faulty harness on switch 

Repair / Replace Harness 

Faulty or disconnected harness 

Check and Repair Harnessing 

Loose connection on Stepper Motor Driver Board Repair connection or

 

Replace

 

Stepper Motor Board 

Faulty Stepper Motor Driver Board 

Repair or Replace Stepper Motor Driver Board 

Faulty Main P.C. board 

Repair or Replace Main P.C. board 

 
Bongo drum will not score 

Power not on sensor 

Check wiring harness for 5 volts on sensor 

Output from sensor not working  

Should be about 5 volts when head is in up position 

Signal gets to main board but board doesn’t see 
it 

Replace mainboard 

 

 
NOTE: CONTACT YOUR DISTRIBUTOR IF NONE OF THE CASES LISTED IN THIS MANUAL APPLIES TO THE PROBLEM, 
OR IF THE ACTION LISTED DOES NOT APPEAR TO RESOLVE THE PROBLEM. 

 

Содержание BONGO BEAT!



























Отзывы: