manualshive.com logo in svg

BSC 615L, Руководство по эксплуатации

Поделиться
Скачать
BSC 615L Скачать руководство пользователя страница 19

BCS Crusader Power Scythes

CPS/MAX/0817

 

Page 19

Use the Handlebar Height Adjustment Lever to set handlebar height.

Pull up the Clutch Lever. This will automatically release the lever Locking Clip.

Ensure the red Forward/Reverse Lever is in the correct position to move forward: if the handlebars 
are positioned over the engine then this lever should be in the fully back position.

Engage drive to the cutter bar by using the PTO Lever: if the handlebars are positioned over the 
engine then pull the PTO Lever towards you.

Using the Wheel Speed Lever, select 1st gear.

Raise the throttle slightly, release the Clutch Lever gently and fully, keeping the red Engine Stop 
(OPC) Lever depressed as the engine will stop if this is released.

Commence work.

IMPORTANT!  NEVER USE MORE THAN ¼ THROTTLE WHEN 
THE CUTTER BAR IS OPERATING

!

Operation

Stopping the Engine

Close the Throttle.

Pull up the Clutch Lever.

Locate the Wheel Speed Lever in neutral position.

Disengage drive to the cutter bar by using the PTO Lever (push the PTO Lever away from you).

Release Clutch Lever.

Release red Engine Stop (OPC) Lever completely.

WARNING: THE EXHAUST COVER MAY BE HOT - DO NOT TOUCH

Содержание 615L





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды