background image

28B-SST Amplifier

3

6. Output binding posts.

The RED binding posts are the in-phase amplifier output. Both red binding posts are the same. Connect either red binding 

post to the (+) terminal on the loudspeaker. The second red binding post is provided for bi-wiring or second loudspeaker.

The BLUE binding posts are the inverted-phase amplifier output Connect either blue binding post to the (-) terminal on the 

loudspeaker. The second blue binding post is provided for bi-wiring or second loudspeaker.

N.B.

At no time should either output be connected to a ground, or chassis. Failure of the 

amplifier may result. Never connect either output in parallel with another amplifier.

N.B.

The minimum recommended loudspeaker load is 4 ohms.

The Output binding posts provide three different interconnect options. Combinations may be used when bi-wiring. See fig-

ure 2 below. Cables should be kept as short as practical and should never be terminated with connectors that may become 

confused for AC power connectors. Cables should be dressed away from input and power cables.

 

 

Banana plugs

 offer a quick disconnect option. Before inserting a banana plug into the binding post be sure to tighten 

the post nut to avoid rattling and to provide full insertion of the banana plug. Gold plated locking banana plugs are 

available from Bryston. 

   

Spade lugs

 provide high contact area and secure fastening. Lugs should be gold plated. See diagram for details. Post 

diameter is 5/16’ ( 8mm ), lug width 5/8” (16 mm). Gold plated spade lugs are available from Bryston. 

 

●    

Stripped bare wire

 up to 3 gage can be inserted through the hole in the binding post and held in place by tightening 

the post knob. Additional tightening pressure can be achieved using a 

coin

 in the slots of the knob. Do not over tighten 

or the binding post may become damaged. Note that copper wire is malleable and may require further tightening after 

the initial installation.

5/8

5/16”

Spade lug dimensions

BANANA 

PLUG

SPADE

LUG

BARE

WIRE

Содержание 28B SST











Отзывы: