background image

H

EAT

72

72

About Advanced Features & Operation

Page 9

KEYPAD LOCK - To prevent unauthorized use of the thermostat,
       the front panel buttons may be disabled.  To disable, or
       ‘lock’ the keypad, press and hold in the On/Off button.
       While holding the On/Off button in, press the Down button,
       while holding the Down button in press the Up button.  The
       keypad is now locked.
        
       
       

Press all 3 for

Keypad Lockout

  
To 

unlock

 the buttons, again press and hold in the On/Off 

 button.   While holding the On/Off button in, press the Down 
 button, while holding the Down button in press the Up button.  
 The keypad is now unlocked.

ON/OFF

FACTORY DEFAULTS - If, for any reason it is desirable to
       return all stored settings back to the factory default
       settings, press the On/Off button.  While holding the On/Off
       button in, press the Down button for 5 sec.  All icons will
       appear.  Press and hold in the Outside button until 

Fd

       appears.  This resets all factory settings. 

To calibrate

       

room temperature,

 press the On/Off button once more.

       At this point use the Up and Down buttons to calibrate
       room temperature, if needed.  Press the On/Off button to
       return to normal operation.  

NOTE CAUTION ON PAGE 1.

Содержание TSTATBBN2W01
















Отзывы: