Bryant LEGACY LINE 13 223A, Данные о продукции

Страница: 5 / 58

5
ACCESSORY THERMOSTATS
THERMOSTAT / SUBBASE
PKG.
DESCRIPTION
T6---PRH---01 Programmable Thermidistat
T6---NRH---01 Non ---programmable Thermidistat
T2---PHP---01 Legacy Line Programmable HP Stat
T2---NHP---01 Legacy Line Non ---programmable HP Stat
TSTATBBPRH01---B*
Thermidistat
t
Control — Non ---Programmable/Programmable Thermostat with Humidity Control (For use in Dual Fuel, AC,
HP, and 2S applications. Includes Outdoor Air Temperature Sensor.)
TSTATBBPHH01---B*
HybridHeat
t
(Dual Fuel) Thermostat — Auto Changeover, 7---Day Programmable,
°
F/
°
C, Includes Outdoor Sensor
(TSTATXXSEN01---B)
TSTATBBPHP01---B Thermostat — Auto Changeover, 7---Day Programmable,
°
F/
°
C, 2---Stage Heat, 1---Stage Cool
TSTATBBNHP01---C Thermostat — Auto Changeover, Non ---Programmable,
°
F/
°
C, 2---Stage Heat, 1---Stage Cool
TSTATBBSHP01 Standard Programmable Thermostat—Manual Changeover, 5---2 Day Programmable,
°
F/
°
C, 1---Stage Heat/ 1---Stage Cool
TSTATBBBHP01* ---B Builder’s Thermostat — Heat Pump, Non ---Programmable,
°
F/
°
C, 2---Stage Heat, 1---Stage Cool, Manual Changeover
TSTATXXSEN01---B** Outdoor Air Temperature Sensor
TSTATXXNBP01 Backplate for Non ---Programmable Thermostat
TSTATXXPBP01 Backplate for Programmable Thermostat and Thermidistat
t
Control
TSTATXXSBP01 Backplate for Standard Programmable Thermostat
TSTATXXBBP01 Backplate for Builder’s Thermostat
TSTATXXCNV10
{
Thermostat Conversion Kit (4 to 5 Wire) — 10 Pack
* Do not use in zoning heat pump applications.
** Outdoor temperature sensor is an accessory for all Bryant electronic thermostats, except the non ---programmable air conditioner version and builder;s
thermostats. It allows the temperature at a remote location (outdoors) to be displayed on the thermostat. The outdoor air temperature sensor must be used
with the HybridHeat
t
(dual fuel) thermostat.
{
Thermostat conversion kit is a 24---vac accessory that can turn a 4---wire thermostat application into a 5---wire application. This kit can also be used to
replace a broken thermostat wire, or add an extra wire when needed.
The outdoor air temperature sensor is included with the Thermidistat Control and HybridHeat
t
(dual fuel) thermostat.
ACCESSORY USAGE GUIDELINE
Accessory
REQUIRED FOR LOW---AMBIENT
COOLING APPLICATIONS
(Below 55
°
F / 12.8
°
C)
REQUIRED FOR
LONG LINE APPLICATIONS*
(Over 80 ft. / 24.38 m)
REQUIRED FOR
SEA COAST APPLICATIONS
(Within 2 miles / 3.22 km)
Accumulator Standard Standard Standard
Ball Bearing Fan Motor Yes
{
No No
Compressor Start Assist Capacitor and
Relay
Yes Yes No
Crankcase Heater Yes
Yes
No
Evaporator Freeze Thermostat Yes No No
Hard Shutoff TXV Yes Yes Yes
Isolation Relay Yes No No
Liquid Line Solenoid Valve No
See Long---Line Application
Guideline
No
Motor Master
®
Control or
Low Ambient Switch
Yes No No
Support Feet Recommended No Recommended
* For tubing line sets between 80 and 200 ft. (24.38 and 60.96 m) and/or 20 ft. (6.09 m) vertical differential, refer to Residential Split---System Longline
Application Guideline.
{
Additional requirement for Low---Ambient Controller (full modulation feature) MotorMaster
r
Control.
Accessory Description and Usage (Listed Alphabetically)
1. Ball--Bearing Fan Motor
A fan motor with ball bearings which permits speed reduction
while maintaining bearing lubrication.
Usage Guideline:
Required on all units when using MotorMaster
r
2. Compressor Start Assist -- Capacitor and Relay
Start capacitor and relay gives a ”hard” boost to compressor
motor at each start up.
Usage Guideline:
Required for reciprocating compressors in the
following applications:
Long line
Low ambient cooling
Hard shut off expansion valve on indoor coil
Liquid line solenoid on indoor coil
Required for single--phase scroll compressors in the
following applications:
Long line
Low ambient cooling
Suggested for all compressors in areas with a history of
low voltage problems.
3. Compressor Start Assist — PTC Type
Solid state electrical device which gives a ”soft” boost to the
compressor at each start--up.
Usage Guideline:
Suggested in installations with marginal power supply.
4. Crankcase Heater
An electric resistance heater which mounts to the base of the
compressor to keep the lubricant warm during off cycles.
Improves compressor lubrication on restart and minimizes the
chance of liquid slugging.
Usage Guideline:
Required in low ambient cooling applications.
Required in long line applications.
Suggested in all commercial applications.
223A