Bryant 935SA Скачать руководство пользователя

Страница: 6 / 60

935SA: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A190256

NOTE:

Downflow not permitted with any return air configuration.

Fig. 4 – Prohibited Installations

A93044

Fig. 5 – Installation in a Garage

CODES AND STANDARDS

Follow all national and local codes and standards in addition to these

instructions. The installation must comply with regulations of the

serving gas supplier, local building, heating, plumbing, and other codes.

In absence of local codes, the installation must comply with the national

codes listed below and all authorities having jurisdiction.
In the United States, follow all codes and standards for the following:

Safety

• Current edition of US: National Fuel Gas Code (NFGC) NFPA

54/ANSI Z223.1 and the Installation Standards, Warm Air Heating

and Air Conditioning Systems ANSI/NFPA 90B

General Installation

• US: NFGC and the NFPA 90B. For copies, contact the National Fire

Protection Association Inc., Batterymarch Park, Quincy, MA 02269;

or for only the NFGC contact the American Gas Association, 400 N.

Capitol, N.W., Washington DC 20001

Combustion and Ventilation Air

• US: Current edition of Section 9.3 of the NFPA54/ANSI Z223.1 Air

for Combustion and Ventilation

Duct Systems

• US: Current edition of Air Conditioning Contractors Association

(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors

National Association (SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE)

Fundamentals Handbook Chapter 35

Acoustical Lining and Fibrous Glass Duct

• US: Current edition of SMACNA, NFPA 90B as tested by UL

Standard 181 for Class I Rigid Air Ducts

Gas Piping and Gas Pipe Pressure Testing

• US: Current edition of NFPA 54/ANSI Z223.1 NFGC; Chapters 5, 6,

7, and 8 and national plumbing codes.

In the state of Massachusetts:

• This product must be installed by a licensed plumber or gas fitter.

• When flexible connectors are used, the maximum length shall not

exceed 36 in. (914 mm).

• When lever type gas shutoffs are used they shall be T-handle type.

• The use of copper tubing for gas piping is not approved by the state of

Massachusetts.

Electrical Connections

• US: Current edition of National Electrical Code (NEC) NFPA 70

Condensate Drain Connection

• US: Current edition of National Standard Plumbing Code, Section 8.7.

ELECTROSTATIC DISCHARGE (ESD)

PRECAUTIONS PROCEDURE

1. Disconnect all power to the furnace. Multiple disconnects may be

required. DO NOT TOUCH THE CONTROL OR ANY WIRE

CONNECTED TO THE CONTROL PRIOR TO DISCHARGING

YOUR BODY’S ELECTROSTATIC CHARGE TO GROUND.

2. Firmly touch the clean, unpainted, metal surface of the furnace

chassis which is close to the control. Tools held in a person’s hand

during grounding will be satisfactorily discharged.

3. After touching the chassis, you may proceed to service the control

or connecting wires as long as you do nothing to recharge your

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

Do not install the furnace on its back or hang furnace with control

compartment facing downward. Safety control operation will be

adversely affected. Never connect return-air ducts to the back of the

furnace (see

Fig. 4

BACK POSITIONED

DOWNWARD

AIR RETURN

CUT IN BACK

BACK POSITIONED

UPWARD

18-IN. (457.2 mm)

MINIMUM TO BURNERS

CAUTION

FURNACE RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.
Electrostatic discharge can affect electronic components. Take

precautions during furnace installation and servicing to protect the

furnace electronic control. Precautions will prevent electrostatic

discharges from personnel and hand tools which are held during the

procedure. These precautions will help to avoid exposing the control to

electrostatic discharge by putting the furnace, the control, and the

person at the same electrostatic potential.

Содержание 935SA





























































Результаты поиска

Содержание 935SA

Отзывы:

Похожие инструкции для 935SA

Бренды по названию

Популярные бренды

Bryant 935SA, Руководство пользователя

Результаты поиска

Содержание 935SA

Отзывы:

Похожие инструкции для 935SA

Бренды по названию

Популярные бренды