Bryant 800SA Скачать руководство пользователя страница 25

Страница: 25 / 40

800SA/801SA: Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A02068

Fig. 39 – Horizontal Right Application-Vent Elbow Left

A03216

Fig. 40 – Horizontal Left Application-Vent Elbow Right

A03215

Fig. 41 – Horizontal Left Application-Vent Elbow Up

A03219

Fig. 42 – Horizontal Right Application-Vent Elbow Left then Up

A03214

Fig. 43 – Horizontal Left Application-Vent Elbow Right then Up

VENTING NOTES FOR

Fig. 31

Fig. 43

1. For common vent, vent connector sizing and vent material: United

States-use the NFGC.

2. Immediately increase to 5-inch (127 mm) or 6-inch (152 mm) vent

connector outside furnace casing when 5-inch (127 mm) vent

connector is required, refer to Note 1 above.

3. Side outlet vent for upflow and downflow installations must use

Type B vent immediately after exiting the furnace, except when

factory-authorized, Downflow Vent Guard Kit, is used in the

downflow position. See Product Data Sheet for accessory listing.

4. Type-B vent where required, refer to Note 1 above.
5. Four-inch single-wall (26 ga. min.) vent must be used inside

furnace casing and when the Downflow Vent Guard Kit is used

external to the furnace. See Product Data Sheet for accessory

listing.

6. Factory-authorized accessory Downflow Vent Guard Kit required

in downflow installations with lower vent configuration. See

Product Data Sheet for accessory listing.

7. Chimney Adapter Kit may be required for exterior masonry

chimney applications. Refer to Chimney Adapter Kit for sizing and

complete application details. See Product Data Sheet for accessory

listing.

8. Secure vent connector to furnace elbow with (2) corrosion-resistant

sheet metal screws, spaced approximately 180° apart.

9. Secure all other single wall vent connector joints with (3) corrosion

resistant screws spaced approximately 120° apart. Secure Type-B

vent

connectors

per vent

connector

manufacturer’s

recommendations.

START-UP, ADJUSTMENT, AND SAFETY

CHECK

GENERAL

SEE NOTES: 1,2,4,5,7,8,9

SEE NOTES: 1,2,4,5,7,8,9 on the page
following these figures

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

This furnace is equipped with manual reset limit switches in the gas

control area. The switches open and shut off power to the gas valve if a

flame rollout or overheating condition occurs in the gas control area.

DO NOT bypass the switches. Correct inadequate combustion air

supply problem before resetting the switches.

SEE NOTES: 1,2,4,5,7,8,9 on the page
following these figures

Содержание 800SA









































Результаты поиска

Содержание 800SA

Отзывы:

Похожие инструкции для 800SA

Бренды по названию

Популярные бренды

Bryant 800SA, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание 800SA

Отзывы:

Похожие инструкции для 800SA

Бренды по названию

Популярные бренды