Bryant 580J*04A Скачать руководство пользователя страница 10

Страница: 10 / 52

Step 7 — Convert to Horizontal and Connect

Ductwork (when required) —

Unit is shipped in the ver-

tical duct configuration. Unit without factory-installed econo-

mizer or return air smoke detector option may be field-convert-

ed to horizontal ducted configuration. To convert to horizontal

configuration, remove screws from side duct opening covers

and remove covers. Using the same screws, install covers on

vertical duct openings with the insulation-side down. Seals

around duct openings must be tight. See Fig. 7.

Fig. 7 — Horizontal Conversion Panels

Field-supplied flanges should be attached to horizontal duct

openings and all ductwork should be secured to the flanges. In-

sulate and weatherproof all external ductwork, joints, and roof

or building openings with counter flashing and mastic in accor-

dance with applicable codes.

Do not cover or obscure visibility to the unit’s informative

data plate when insulating horizontal ductwork.

Step 8 — Install Outside Air Hood

ECONOMIZER AND TWO POSITION DAMPER HOOD
PACKAGE REMOVAL AND SETUP — FACTORY

OPTION

NOTE: Economizer and two position damper are not avail-

able as factory installed options for single phase (-J voltage

code) models.

1. The hood is shipped in knock-down form and must be

field assembled. The indoor coil access panel is used

as the hood top while the hood sides, divider and filter

are packaged together, attached to a metal support tray

using plastic stretch wrap, and shipped in the return air

compartment behind the indoor coil access panel. The

hood assembly’s metal tray is attached to the basepan

and also attached to the damper using two plastic tie-

wraps.

2. To gain access to the hood, remove the filter access panel.

See Fig. 8.

Fig. 8 — Typical Access Panel Locations

3. Locate the (2) screws holding the metal tray to the base-

pan and remove. Locate and cut the (2) plastic tie-wraps

securing the assembly to the damper. (See Fig. 9.) Be

careful to not damage any wiring or cut tie-wraps secur-

ing any wiring.

Fig. 9 — Economizer and Two-Position Damper Hood

Parts Location

4. Carefully lift the hood assembly (with metal tray) through

the filter access opening and assemble per the steps out-

lined in

Economizer Hood and Two–Position Hood

, be-

low.

ECONOMIZER HOOD AND TWO-POSITION HOOD

NOTE: If the power exhaust accessory is to be installed on

the unit, the hood shipped with the unit will not be used and

must be discarded. Save the aluminum filter for use in the

power exhaust hood assembly.

REMOVABLE HORIZONTAL

RETURN DUCT OPENING COVER

REMOVABLE HORIZONTAL

UPPLY DUCT OPENING COVER

COMPRESSOR
ACCESS PANEL

OUTDOOR-AIR OPENING AND
INDOOR COIL ACCESS PANEL

FILTER ACCESS PANEL

Hood Parts

Plastic Tie Wrap
Qty (2)

Screws for Metal Tray
Qty (2)

Содержание 580J*04A





















































Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды

Bryant 580J*04A, Руководство по установке

Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды