Bruno ELECTRA-RIDE LT Скачать руководство пользователя страница 41

FIVE YEAR MAJOR COMPONENTS WARRANTY

TWO YEAR LIMITED WARRANTY

for 

Bruno Stairlifts

Bruno Independent Living Aids, Inc. (“Bruno”), warrants to the original purchaser of a Bruno 

Stairlift that the Bruno Stairlift is free from defects in material and workmanship for a period 

of two years from date of purchase.  In addition, Bruno warrants that the motor, gear box and 

rail (the “Major Components”) will be free from defects in materials and workmanship for a 

period of five years from the date of purchase.
The exclusive remedy for a defect in a Bruno Stairlift shall be the repair or replacement, at the 

option of Bruno, of the defective part or component. After the first 30 days of this warranty, 

only parts and components are covered. This warranty does not cover labor and other

services after the initial 30 days. If repair or replacement of a Bruno Stairlift is not  

commercially practical or cannot be timely made, Bruno may elect to refund the purchase price 

of the Bruno Stairlift instead of repairing or replacing the Bruno Stairlift.

IN NO EVENT SHALL BRUNO BE RESPONSIBLE FOR INDIRECT, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES, WHETHER SUCH DAMAGES ARISE FROM CLAIMS BASED 

ON CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE), STRICT 

LIABILITY OR  PRODUCT LIABILITY. 

Some states do not allow the exclusion or limitation 

of incidental or consequential damages, so the above limitation or exclusion may not apply to 

you.

ALL IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR 

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN THEIR DURATION TO THE 

LENGTH OF THE WARRANTY STATED ABOVE FOR THE AFFECTED COMPONENT. 

Some 

states do not allow limitations on how long an implied warranty lasts so the above limitation may 

not apply to you.
 

To obtain warranty service, you must follow these procedures:

 

 

1. 

Obtain return authorization by calling your local Bruno dealer;

 

2. 

Return the Bruno Stairlift, freight prepaid, to the address provided by your    

 

Bruno dealer or Bruno with proof of purchase indicating the date purchased.

Bruno will pay for shipping back to the purchaser within the continental United States and 

Canada if a defect in material or workmanship is discovered. Return freight and repair charges 

will be the responsibility of the purchaser if the problem is not covered by warranty.

 

This warranty does not cover damage or failure caused by misuse, abuse, accidents, physical 

damage, modifications not made by Bruno, damage in shipment, or repairs  

undertaken by anyone other than Bruno factory employees or authorized distributors. The 

“original purchaser” of a Bruno Stairlift that is leased or rented shall be the person or entity 

acting as the lessee or rental provider.
This warranty gives you specific legal rights, and you may also have other rights which vary 

from state to state. Bruno specifically does not authorize any person to extend the time or 

scope of this warranty.
For further information regarding this limited warranty, please contact Bruno by calling  

1-800-882-8183 or writing to Bruno at the following address:

  

 

 

 

 

Bruno Independent Living Aids, Inc.®

    Attention: 

Service 

Department

 

 

 

 

1780 Executive Drive, P. O. Box 84

    Oconomowoc, 

WI 

53066 

USA

Содержание ELECTRA-RIDE LT











































Отзывы: