BRUEL & KJAER PULSE 7788 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 62

BRUEL & KJAER PULSE 7788 Скачать руководство пользователя страница 26

Systems –

Installation

20

Note:

The Ground Station runs continuously and measures the acoustic signals, photocell

signals, radar and weather station data, if present. This information is continuously

broadcast to the Vehicle Station using a remote station server and client to manage the

data transfer. These two components control communication between the Ground

Station (server) and the Vehicle Station (client).

5.1.1

Measurement

Control

A measurement run is started on the Vehicle Station PC by the operator activating the

system then clicking start in the Vehicle Station measurement control interface or by

triggering with a vehicle-mounted photocell.
Fig.5.2 shows the measurement control interface in the software.

Fig.5.2

The

PBY

Vehicle

Pass

‐

by

software

module

during

operation

The measurement run is started on the Ground Station when the ground-mounted

photocells are triggered.
Fig.5.3 shows the interface of the dedicated Ground Station software. After setup, the

interface need not be monitored, as the software will run on its own.

«
...
24
25
26
27
28
...
»

Содержание PULSE 7788































































Отзывы:

Нет отзывов