manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 58 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 58

56

ENGINE MANAGEMENT MODULE (EMM)

INTERNAL EMM FUNCTIONS

INTERNAL EMM 
FUNCTIONS

ROM Verification

The 

EMM

 performs a self-test of programming

every time it is turned ON. Service code 15 indi-
cates a programming (software) issue. Repro-
gram the 

EMM

 with the correct software program

to correct the problem.

Idle Controller

The idle controller reacts to engine operating con-
ditions. Fuel and ignition timings are altered to
maintain a specific RPM when engine is cold or
warm. The controller is inactive when TPS is
advanced from idle position.

RPM Limiter

This feature of 

EMM

 programming prevents

engine damage due to excessive RPM. At 6250
RPM, fuel and ignition to the cylinders is shut off.
Normal operation resumes when engine RPM
returns to the specified range.

Neutral RPM Limiter

This feature prevents engine damage due to
excessive RPM if accelerated in NEUTRAL. Neu-
tral engine speed is limited to 1100 RPM.

Engine Monitor and Warning 
Systems

Refer to 

ENGINE MONITOR SYSTEM

 on p. 56.

Refer to 

S.A.F.E. WARNING SYSTEM

 on p. 57.

Refer to 

SHUTDOWN MODE

 on p. 58.

Fault Code Creation and Storage

Refer to the 

EMM Service Code Chart

 at the

back of this manual for a complete list of all
engine fault codes.

ENGINE MONITOR 
SYSTEM

An optional engine monitoring system warns the
operator of conditions that could damage the out-
board. The system includes a LOW OIL switch on
the oil tank, a warning horn, a dash-mounted dis-
play, and related wiring.

The outboard’s 

EMM

 sends information about

monitored functions to:

•

A 

SystemCheck

 gauge

•

EMM

 LED indicators

IMPORTANT:

Evinrude E-TEC

 15–30 HP mod-

els provide LOW OIL warning ONLY.

The 

EMM

 activates the warning horn and gauge

displays as follows:

•

LOW OIL means that oil in the tank is at reserve
level (about 1/4 full).

For all other warnings, refer to 

EMM LED INDICA-

TORS

 on p. 71.

Refer to the 

EMM Service Code Chart

 at the

back of this manual for a complete list of all fault
codes.

Typical SystemCheck gauges

007384

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов