BRP Evinrude E-TEC Series Скачать руководство пользователя страница 272

Страница: 272 / 342

270

TRIM AND TILT

ROUTINE INSPECTIONS

ROUTINE INSPECTIONS

General

Check for external signs of fluid leakage. Correct
causes as necessary.

Check the battery and make sure it is in good
operating condition.

Reservoir Fluid

Check reservoir fluid level at least every three
years or 300 operating hours. System capacity is
approximately 15.2 fl. oz. (450 ml).

IMPORTANT:

Use only

Evinrude/Johnson

Bio-

degradable TNT

Fluid to fill the hydraulic system.

Refer to

Trim and Tilt

on p. 35 for filling proce-

dure.

Manual Release Valve

Check the manual release valve with a torque
wrench.

IMPORTANT:

Tighten valve to a torque of 45 to

55 in. lbs. (5 to 6 N·m).

Stern Brackets

Inspect the stern brackets for binding.

Tighten starboard tilt tube nut to a torque of 45 to
50 ft. lbs. (61 to 68 N·m).

TROUBLESHOOTING

Use the following guidelines to check a single pis-
ton trim/tilt unit that is not working correctly.

Cylinder Leakdown:

•

Manual release valve seals

•

External leaks

No reverse lock:

•

External leaks

No operation, motor runs:

•

Manual release valve open

•

Fluid level low

•

Pump coupler

•

Hydraulic pump

No tilt down:

•

Manual release valve

•

Fluid level

Slow performance:

•

Manual release valve

•

Fluid level low

•

Mechanical binding

•

Electric motor

•

Hydraulic pump

Unit locked in tilt up:

•

Mechanical binding

•

Hydraulic pump

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 272 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: