manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 191 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 191

189

POWERHEAD

POWERHEAD INSTALLATION

10

Place the upper shift rod in the shift rod connector.
Install the retaining screw and lock washer.
Tighten  screw to a torque of 60 to 84 in. lbs. (7 to
9.5 N·m).

Install water screens.

Check shift linkage adjustment. Refer to 

Shift

Linkage Adjustment

 on p. 189.

IMPORTANT:

Make sure the gearcase shifts

solidly into both forward and reverse and that pro-
peller shaft spins freely in neutral.

Connect the power trim connectors. Secure
cables in clamps.

Install recoil starter ratchet and housing on out-
board. Refer to 

RECOIL STARTER INSTALLA-

TION

 on p. 282.

Install the lower engine covers. Refer to 

Lower

Cover Installation

 on p. 45.

Shift Linkage Adjustment

Adjust shift linkage as follows:

STEP 1:

 Move shift lever into neutral position.

•

Make sure shift lever detent is in neutral posi-
tion. 

•

Make sure gearcase is in neutral.

•

Loosen two shift lever screws.

STEP 2:

 Find shift lever midpoint.

•

Move the shift lever forward to the limit of free
play. Mark this as forward line on the neutral
detent.

•

Move the shift lever rearward to the limit of free
play. Mark this as rearward line on the neutral
detent.

•

Measure the midpoint between the forward and
rearward lines. Make a third line on the on the
neutral detent. Mark this as midpoint line.

•

Align the shift lever to the midpoint line.

1.

Shift rod screw

7650

1

1.

Shift lever

2.

Shift lever detent

3.

Shift lever screws

008461

1.

Forward line

2.

Rearward line

3.

Midpoint line

008461

1

2

3

2

3

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов