BRP Can-Am Spyder RT 2013 Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 47

background image

rbl2013-002-006_a

1. Fender light connector

rbl2013-002-009_a

1. Cable grommet
2. Harness bracket

5. Secure fender support on wheel hub.

6. Remove protection from suspension arms.

rbl2013-002-008_b

1. M8 x 20 hexagonal flange screws

7. Install 4 M8x 20 hexagonal flange screws to

complete the fender support installation.

FENDER SUPPORT RETAINING SCREW

24 N•m (18 lbf•ft)

8. Carry out the same procedure for the other

side.

Windshield

1. Install spacer on windshield support as illus-

trated.

rbl2012-002-001_a

1. Windshield spacer

2. Align windshield on windshield support.

3. Install M6 x 20 Torx screws (from PDI kit) to

secure windshield.

rmr2010-038-045_a

1. Windshield M6 x 20 screws

4. Torque windshield retaining screws.

PART

TORQUE

Windshield retaining

screw

4.5 N•m (40 lbf•

in

)

5. Install windshield trim panels as follows:

5.1 Insert M5 retaining nut (from PDI kit) on

trim panel.

20 / 47

2013-2

SERVICE

«
...
18
19
20
21
22
...
»

Содержание Can-Am Spyder RT 2013 Series
















































Отзывы:

Нет отзывов

Похожие инструкции для Can-Am Spyder RT 2013 Series

Бренд: KYMCO Страницы: 424

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

KTM390-14-01-SL

Бренд: SRC Страницы: 4

Бренд: PUIG Страницы: 6

Бренд: Crivit Страницы: 30

Бренд: Wolfman Страницы: 3

Spyder RT Series

Бренд: Can-Am Страницы: 52

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Honda Страницы: 93

Dirt rocket XM500

Бренд: X-TREME scooter Страницы: 14

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 2

Бренд: hepco & becker Страницы: 3

Scorpion 608-30-10086

Бренд: Barnett Страницы: 2

Бренд: TM Страницы: 80

Бренд: R&G Страницы: 9

Бренд: Saddlemen Страницы: 2

Express Trunk Bag

Бренд: Saddlemen Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды