Brother S-7000DD Скачать руководство пользователя страница 23

Страница: 23 / 52

S-7000DD

3. USING THE OPERATION PANEL (BASIC OPERATIONS)

3-2. Sewing start and end backtack stitches

0841M

Setting start backtack stitches

Setting end backtack stitches

Start backtacking is carried out. After it has finished, normal sewing continues for as long as
the treadle remains depressed.

NOTE:

If the treadle is returned to the neutral position, the sewing machine will continue
operating until the set number of start backtack stitches has been sewn.

End backtacking is carried out. After it has finished, the thread is trimmed automatically and
the sewing machine stops in the needle up position.

NOTE:

・

If the treadle is depressed backward before sewing of the set number of start backtack
stitches is complete, end backtacking will not be carried out.

・

If thread trimming lock is set, the sewing machine will stop in the needle up position
without thread trimming being carried out.

0499D

For example,
3 stitches and
4 stitches

Example:

2159M

2160M

0500D

Содержание S-7000DD





















































Результаты поиска

Содержание S-7000DD

Отзывы:

Похожие инструкции для S-7000DD

Бренды по названию

Популярные бренды

Brother S-7000DD, Инструкция по эксплуатации

Результаты поиска

Содержание S-7000DD

Отзывы:

Похожие инструкции для S-7000DD

Бренды по названию

Популярные бренды