manualshive.com logo in svg

Brother HL-5580D, Руководство по обслуживанию

Поделиться
Скачать
Brother HL-5580D Скачать руководство пользователя страница 362

5-13

Confidential

1.3.6 Display software version (function code: 25)

<Function>

This function is used to check the version information of the firmwares and programs, or 
check sum information.

<Operating Procedure>

*1

How to display the check sum information
You can check the check sum information by pressing the [OK] key while each version 
is displayed. When the [OK] key is pressed again, the LCD returns to the version 
display.

*2

(P) indicates that the firmware supports PCL/PS.

*3

There are two types of check sum information that can be checked with this function. 
This function checks if the two types of check sum information match each other.
When the [OK] key is pressed while "ROM Check Sum" is displayed, check is 
automatically conducted for each ROM of each software part. When the check sum 
matches, "OK" is displayed on the LCD. When all ROMs result in OK, "ROM Check 
Sum OK" is displayed at the end, and the operation is finished. When the check sum 
of any ROM does not match, "NG" is displayed, and the display stops.

*4

This is displayed on the LCD even no firmware is installed.

*5

Displayed only for font firmware support model.

Non touch panel models
(1) Press the [

▲

] or [

▼

] key in the initial 

state of maintenance mode to display 
"MAINTENANCE 25" on the LCD, and 
press the [OK] key. "MAIN:Ver*.** (#)" 
is displayed on the LCD.

(2) Pressing the [Go], [

▲

] or [

▼

] key 

changes the display item as shown in 
the table below.

(3) Press the [X] key, and the machine 

returns to the initial state of 
maintenance mode.

Touch panel models
(1) Press the [2], and then the [5] key in 

the initial state of maintenance mode. 
"MAIN:Ver*.** (#)" is displayed on the 
LCD.

(2) Pressing the [

▲

], [

˄

], or [Mono] key 

changes the display to the next item.

(3) When you press the [X] key, this 

operation is finished and the machine 
returns to the initial state of 
maintenance mode.

LCD

Description

MAIN: Ver1.00 (A) 

*1

Main firmware version information
((A): Revision information)

SUB1 : Ver1.00 (P)

 *1

Sub firmware version information
((P): Identifier for PCL/PS)

 *2

ENG: Ver.1.00

Do not refer to this item because it has nothing to do with DL.

NET : Ver1.00

Network program version information

MX :Ver1.00

MX firmware version information

TT :Ver1.00

TT firmware version information

LT1 :Ver1.00

LT1 firmware version information

LT2 :Ver1.00

LT2 firmware version information

LT3 :Ver1.00

LT3 firmware version information

B0608071049:5708

 *1

Boot program creation date

U0612271600:7B0A

 *1

Main firmware creation date

D----------:----

 *4

Demo firmware data creation date

F0612312359:1234

 *5

Font firmware creation date

P0612271602:BD40

 *1

Sub firmware (PCL/PS) creation date

ROM Check Sum

Check sum self-diagnosis function

 *3

Содержание HL-5580D


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды