Brother DCP-J925DW Скачать руководство пользователя страница 213

Страница: 213 / 378

3-76

Confidential

9.10 Upper Cover, Ink Cartridge Cover and Media Module Cover

(1) Open the ink cartridge cover.

(2) Remove the five screws (four screws if the front cover has been removed in the previous

section) from the upper cover.

(3) Hold the right and left sides of the upper cover and lift it up and off the lower cover.

Note:

Do not put your hands into the opening above the platen (shown below). Doing so

may damage or stain the CR encoder strip inside.

Assembling Notes:

• When mounting the upper cover:

- Make sure that the ink cartridge cover is opened.

- Make sure that the head/carriage unit is placed in the head capping position (home

position). This prevents the ink supply tubes from getting crushed between the upper and
lower covers.
(If the head/carriage unit remains removed in

Section 9.3

, take care not to crush the ink

supply tubes or carriage flat cables between the upper and lower covers.)

- Take care not to deform the PF encoder disc.

- Be sure to fit the hooks provided on the inside of the upper cover into the groove in the

lower cover.

• After mounting the upper cover, check that the PF encoder disc is not bent or deformed.

Taptite, bind B
M4x12

Opening above the platen

Upper cover

PF encoder disc

Ink cartridge cover

CR encoder strip

Lower cover

Hooks

* This screw has been removed
for removal of the front cover
in Section 9.9.

(3_072)

Содержание DCP-J925DW



























































































































































































































































































































































































Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды

Brother DCP-J925DW, Руководство по обслуживанию

Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды