Brother BE-438FX Скачать руководство пользователя страница 87

Страница: 87 / 90

11. TROUBLESHOOTING

Problem

Cause

Remedy

Ref.

Upper thread is not
trimmed.

Movable knife is blunt.

Replace the movable knife.

P. 68

Fixed knife is blunt.

Sharpen or replace the fixed knife.

P. 68

Movable knife does not pick up the
thread.

Adjust the position of the shuttle race
thread guide.

P. 67

Adjust the needle bar lift amount.

P. 66

The movable knife does not pick up the
thread because of skipped stitches at
the sewing end.

Refer to “Skipped stitches occur”.

P. 77

Movable knife position is incorrect.

Adjust the position of the movable
knife.

P. 68

Sub-tension is too weak.

Turn the sub-tension nut to adjust the
tension.

P. 30

Thread jamming.

Thread take-up spring tension and
height are incorrect.

Adjust the tension and height of the
thread take-up spring.

P. 64

Incorrect needle and rotary hook timing.

Adjust the needle bar lift amount.

P. 66

Shuttle race thread guide is not
separating the threads.

Adjust the position of the shuttle race
thread guide.

P. 67

Poor seam finish on
reverse side of
material.

Shuttle race thread guide is separating
the threads insufficiently.

Adjust the position of the shuttle race
thread guide.

P. 67

Upper thread is not properly tight.

Adjust the upper thread tension.

P. 63

Uneven needle thread.

Adjust the sub-tension.

P. 30

Needle thread is too long.

Adjust the sub-tension.

Turn the tension nut to adjust the upper
thread trailing length to 35 – 38 mm.

P. 30

Needle is striking the button.
(BE-438FX)

Refer to “5-5. Checking the sewing
pattern”.

P. 42

Incorrect thread
tightness.

Upper thread tension is too weak.

Adjust the upper thread tension.

P. 63

Lower thread tension is too weak.

Adjust the lower thread tension.

P. 63

Thread take-up spring tension and
height are incorrect.

Adjust the tension and height of the
thread take-up spring.

P. 64

Machine does not
operate when power is
turned on and foot
switch is depressed.

Machine head switch does not work.

Check if the machine head switch cord
is disconnected.

P. 17

Adjust the position of the switching
plate.

P. 25

Replace the machine head switch if it is
broken.

KE-430FX/KE-430FS, BE-438FX

Содержание BE-438FX



























































































Результаты поиска

Содержание BE-438FX

Отзывы:

Похожие инструкции для BE-438FX

Бренды по названию

Популярные бренды

Brother BE-438FX, Инструкция по эксплуатации

Результаты поиска

Содержание BE-438FX

Отзывы:

Похожие инструкции для BE-438FX

Бренды по названию

Популярные бренды