Brother 885-V35 Скачать руководство пользователя страница 14

Страница: 14 / 192

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Needle and presser foot
section

Buttonhole lever

(

page 90

)

Lower the buttonhole lever when sewing buttonholes
and bar tacks.

Thread guide disk (page 34

)

Pass the thread through the thread guide disk when
using the needle threader to thread the needle.

Needle bar thread guide (page 34)

Pass the upper thread through the needle bar thread
guide.

Needle plate (page 70)

The needle plate is marked with guides for sewing
straight seams.

Needle plate cover (page 174)

Remove the needle plate cover to clean the bobbin case
and race.

Bobbin cover/bobbin case (page 28)

Remove the bobbin cover, and then insert the bobbin
into the bobbin case.

Feed dogs

(

page 92

)

The feed dogs feed the fabric in the sewing direction.

Presser foot (page 43, 54)

The presser foot applies pressure consistently on the
fabric as the sewing takes place. Attach the appropriate
presser foot for the selected stitching.

Presser foot holder

(

page 45

)

The presser foot is installed onto the presser foot holder.

Right-side/rear view

Handle

Carry the sewing machine by its handle when
transporting the machine.

Handwheel (page 54)

Turn the handwheel toward you (counterclockwise) to
raise and lower the needle to sew one stitch.

Embroidery card slot (page 156)

Insert the embroidery card.

USB port (page 170)

Connect the one end of the USB cable to this port and
the other to the computer.

Air vent

The air vent allows the air surrounding the motor to be
exchanged. Do not cover the air vent while the sewing
machine is being used.

Main power switch (page 17)

Use the main power switch to turn the sewing machine
on and off.

Foot controller jack (page 56)

Insert the plug on the end of the foot controller cable
into the foot controller jack.

Power supply jack (page 17)

Insert the plug on the power supply cord into the power
supply jack.

Drop feed lever

(

page 92

)

Use the drop feed lever to lower the feed dogs.

Memo

Refer to pages 11 through 14 while you are
learning to use your machine.

Содержание 885-V35

































































































































































































Результаты поиска

Содержание 885-V35

Отзывы:

Похожие инструкции для 885-V35

Бренды по названию

Популярные бренды

Brother 885-V35, Руководство по эксплуатации

Результаты поиска

Содержание 885-V35

Отзывы:

Похожие инструкции для 885-V35

Бренды по названию

Популярные бренды