unPacking and setting uP
Setting Up -
steP 3
Setting Up -
steP 7
Setting Up -
steP 4
Setting Up -
steP 5
Setting Up -
steP 6
Now the mattress is laying upside down on your platform bed surface or
other foundation.
Unzip the cover to expose the cut-away blocks (the head of the mattress should have
the number “1”. The foot of the mattress should have the number “3”).
cautiOn
- Do not plug in any components until instructed to do so.
Remove the six large foam blocks. These spaces will contain the six Massage Modules.
IMPORTANT: Massage Modules must be placed in the corresponding “1”, “2”, and “3”
spaces with the LEFT SIDE and RIGHT SIDE orientation.
Remove the two smaller blocks. These are for the LEFT and RIGHT side
Massage Controllers.
Note: Twin/Full size models have only a single set of THREE large foam blocks and
ONE massage controller.
Unwrap the SIX large Massage Modules and line them up next to the corresponding
“1”, “2”, and “3” spaces with the LEFT SIDE and RIGHT SIDE orientation.
Connect the three LEFT SIDE Massage Modules to the LEFT SIDE Massage
Controller Unit.
Repeat the same process for the RIGHT SIDE.
Insert all SIX Massage Modules and TWO Massage Controller Units.
Place the large Tape Squares over each of the eight inserts to hold them in place.
Note: Twin/Full size models have only a single set of THREE large foam blocks and
ONE massage controller.
Before zipping up the mattress cover, insert the power cord coming from the LEFT
Massage Controller through the grommet hole as shown.
Zip up the Mattress Cover just enough to get the RIGHT Massage Controller power
cord through the other grommet hole as shown.
Flip over your mattress (this could be a two-person job).
With your mattress now turned right side up, connect the Massage Controller power
cords to the AC power cord, making sure the connection is tight. Make sure the power
cords are not pinched or otherwise restricted.
For Queen/King sizes, there are two separate AC power cords for each side of the
bed. For Twin/Full sizes, there is only one power cord.
Each AC power cord should be plugged into a grounded wall socket or surge-
protected power strip.
Press the POWER button on your Remote Control unit to turn on the massage function.
nOte
- Queen/King sizes have TWO separate remote control devices. Twin/Full size
models have only one Remote Control device.
Unpacking the Mattress -
steP 2
neXt
Roll out the mattress onto your foundation/
platform with the bottom side facing up. You’ll know
the mattress is in the right position when the Vivon
logo is upside down and at the foot of your bed
with the zipper-side (bottom) facing up.
Wait!
Do not proceed until you have a place to put your mattress. It is much easier
to move while it is still compressed within the plastic sleeve.
FinaLLY
Using scissors, cut the edges of the plastic sleeve on each side. Pull away
the plastic wrapping and discard.
neXt
With the outer bag removed, cut the straps of
tape as shown. The mattress can now be rolled out.
First
The rolled mattress is covered by a white bag.
Remove the white bag by using scissors to cut the
drawstring at the top and make a small cut into the
white bag materials. Do not use scissors to cut away
the rest of the white bag. Once the material has been
cut, it can be easily ripped by pulling on two sides.
cautiOn
- Be careful not to puncture the inner
clear plastic sleeve at this stage.
Setting Up -
steP 1
Prepare a place for your mattress (platform bed, box spring or Vivon Riser™).
Be sure your mattress is evenly and well supported and close to a grounded
wall outlet.
nOte
- The mattress must be supported properly and not sag anywhere.
Vivon Riser™ mattress
foundation shown. (Not
included, sold separately).
1
2
3
1
2
3
right side
(when flipped over)
LeFt side
(when flipped over)
right side
(when flipped over)
LeFt side
(when flipped over)
2
3
1
1
2
3
right side
grOMMet hOLe
LOcatiOn
(When
cOVer is ZiPPed uP )
LeFt side grOMMet
hOLe LOcatiOn
(When cOVer is ZiPPed uP )
Figure 1
