manualshive.com logo in svg

Brookfield HA, Руководство по эксплуатации

Поделиться
Скачать
Brookfield HA Скачать руководство пользователя страница 15

  Brookfield Engineering Laboratories, Inc.

Page   13

Manual No. M/85-150-N898

Each of the five available cones has a specific sample volume, as shown in Table A1.  Note that the correct
amount of sample fluid should cover the cone face and back up over the edge less than 1mm as shown
in (Figure A8).

Figure A8

Notes:

a) The cup may be removed without resetting the gap.
b) Remove the spindle from the viscometer when you clean it.
c) Refind the hit point every time the spindle is attached.

Table A1

Cone

Sample Volume

Cone Angle

CP-40

0.5 ml

0.8

°

CP-41

2.0 ml

3.0

°

CP-42

1.0 ml

1.565

°

CP-51

0.5 ml

1.565

°

CP-52

0.5 ml

3.0

°

Sample

Cup

Cone

Less than 

1 mm

Cone

Less Than

1 mm

Cup

Sample

Calibration Procedure using Cone/Plate Viscometer

1) Ensure that the circulating bath used maintains the stated calibration temperature to within

±

0.1

°

C.

2) The attachment of the cone spindle and sample cup, and the gap setting between the cone and

cup must be accomplished by following "Cone/Plate Rheometer Set Up" Procedure.

3) Put the proper amount of viscosity standard fluid into the sample cup.  The amount varies per

cone spindle (refer to Table A1).

Содержание HA





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды