BRONKHORST LIQUI-FLOW L13 Скачать руководство пользователя

Страница: 25 / 50

______________________________________ Bronkhorst

______________________________________

________________________________________________________________________________________________

9.17.161

µ-FLOW & LIQUI-FLOW Instruction Manual L01, L13(I), L23(I), L13V12, L23V12

Page 25 of 50

•

(green/red) Module status (MOD; right)

The tables on the next page list the different LED indications.

Network status

Pattern

Time

Indication

•

off

continuous

Power off or offline

•

on, green

continuous

Online, connected, link OK

•

blinking, green

0.5 sec on,

0.5 sec off

Online, not connected; the instrument is online but has no connections to

other nodes or is not allocated tpo a master

•

blinking, red

0.5 sec on,

0.5 sec off

Connenction timed out

•

on, red

continuous

Critical link failure; the device cannot connect to the network

Module status

Pattern

Time

Indication

•

off

continuous

No power

•

on, green

continuous

Normal operation mode

•

blinking, green

0.5 sec on,

0.5 sec off

Device is in standby mode or configuration is missing, incomplete or

incorrect

•

alternating

0.5 sec on,

0.5 sec off

Self test mode

•

on, red

continuous

Critical error; the instrument needs servicing before it can be used

4.11.2.

Multifunctional switch

Some special functions of the instrument can be started manually using the multifunctional switch near the indication

LEDs. These functions are available in analog as well as in digital operation mode.

4.11.2.1. Normal operating functions

•

In order to access these functions, press and hold the switch while the instrument is in normal operation mode

(green LED glowing).

•

As long as the switch is held, the LEDs show a repeating sequence of patterns, where each pattern indicates a

function.

•

All indications in this sequence are continuous.

•

Each pattern is shown for a number of seconds; in the table below the column Hold time indicates the time frame

within the sequence where the LEDs show the associated pattern.

•

To start a function, release the switch when the LEDs show the pattern of the required function.

•

Green

•

Red

Hold time

Function

off

0…1 sec

No action

off

1…4 sec

1. In case of a min/max alarm: reset alarm

2. FLOW-BUS: Auto-install to bus - lets instrument obtain free node address if

configured node address is occupied

Note: min/max alarm (if any) has to be reset before auto install can be performed.

Содержание LIQUI-FLOW L13



















































Результаты поиска

Содержание LIQUI-FLOW L13

Отзывы:

Похожие инструкции для LIQUI-FLOW L13

Бренды по названию

Популярные бренды

BRONKHORST LIQUI-FLOW L13, Инструкция по эксплуатации

Результаты поиска

Содержание LIQUI-FLOW L13

Отзывы:

Похожие инструкции для LIQUI-FLOW L13

Бренды по названию

Популярные бренды