BRONKHORST EL-PRESS Metal sealed Скачать руководство пользователя

Страница: 22 / 45

Bronkhorst®

Instruction Manual EL-PRESS™

9.17.101I

Module status

Pattern

Time

Indication

•

off

continuous

No power

•

on, green

continuous

Normal operation mode

•

blinking,

green

0.5 sec on,

0.5 sec off

Device is in standby mode or configuration is missing, incomplete or incorrect

•

alternating 0.5 sec green,

0.5 sec red

Self test mode

•

on, red

continuous

Critical error; the instrument needs servicing before it can be used

3.5.2

Multifunctional switch

Some special functions of the instrument can be started manually using the multifunctional switch near the indication

LEDs. These functions are available in analog as well as in digital operation mode.

3.5.2.1

Normal operating functions

In order to access these functions, press and hold the switch while the instrument is in normal operation mode (green

LED glowing).

As long as the switch is held, the LEDs show a repeating sequence of patterns, where each pattern indicates a function.

All indications in this sequence are continuous.

Each pattern is shown for a number of seconds; in the table below the column

Hold time

indicates the time frame within

the sequence where the LEDs show the associated pattern.

To start a function, release the switch when the LEDs show the pattern of the required function.

•

(green)

•

(red)

Hold time Function

off

0…1 sec

No action

off

1…4 sec

1. In case of a min/max alarm: reset alarm

2. FLOW-BUS: Auto-install to bus - lets instrument obtain free node address if

configured node address is occupied

Note: min/max alarm (if any) has to be reset before auto install can be performed.

off

4…8 sec

Reset instrument; clear all warnings and error messages and restart the instrument

off

8…12 sec Auto-zero; re-adjust the zero-point of the instrument (flow meters/controllers only)

12…16 sec Enable FLASH mode for firmware update:

the instrument shuts down and both LEDs are switched off

at the next power-up, the instrument will be active again

Содержание EL-PRESS Metal sealed














































Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды

BRONKHORST EL-PRESS Metal sealed, Инструкция по эксплуатации

Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды