BRONKHORST EL-FLOW Select Series, Инструкция по эксплуатации

Страница: 45 / 53

Bronkhorst®
Instruction Manual EL-FLOW® Select 9.17.099J 45
Capacity 100%
Type Access Range FlowDDE FLOW-BUS Modbus
Float RW B 1E-10…
1E+10
21 1/13 0x8168…0x8169/33129…33130
·
This parameter represents the 100 % readout/control value (span) for the selected fluid, expressed in the selected Capacity
Unit .
·
Capacity 100% is scaled when Inlet Pressure , Fluid Temperature or Fluid Name is changed for the selected fluid.
Capacity Unit
Type Access Range FlowDDE FLOW-BUS Modbus
Unsigned char[7] RW B see below 129 1/31 0x81F8…0x81FB/33273…33276
This parameter represents the unit in which the Capacity 0%/100% parameters are expressed.
Available units:
Mass flow Normal volume flow
(1.01325 bar(a), 0 °C)
Standard volume flow
(1.01325 bar(a), 20 °C)
Custom volume flow
( Capacity Unit Type Pressure ,
Capacity Unit Type
Temperature )
ug/h, ug/min, ug/s,
mg/h, mg/min, mg/s,
g/h, g/min, g/s,
kg/h, kg/min, kg/s
uln/h, uln/min, uln/s,
mln/h, mln/min, mln/s,
ln/h, ln/min, ln/s,
ccn/h, ccn/min, ccn/s,
mm3n/h, mm3n/m,
mm3n/s,
cm3n/h, cm3n/m, cm3n/s,
m3n/h, m3n/min, m3n/s,
scfh, scfm, scfs,
sccm, slm
uls/h, uls/min, uls/s,
mls/h, mls/min, mls/s,
ls/h, ls/min, ls/s,
ccs/h, ccs/min, ccs/s,
mm3s/h, mm3s/m, mm3s/s,
cm3s/h, cm3s/m, cm3s/s,
m3s/h, m3s/min, m3s/s
ul/h, ul/min, ul/s,
ml/h, ml/min, ml/s,
l/h, l/min, l/s,
cc/h, cc/min, cc/s,
mm3/h, mm3/m, mm3/s,
cm3/h, cm3/m, cm3/s,
m3/h, m3/min, m3/s,
cfh, cfm, cfs
Because of the maximum string length (7 characters), some unit names are abbreviated. For instance mm3n/m means
mm
3
n/min.
Capacity Unit Type Temperature
Type Access Range FlowDDE FLOW-BUS Modbus
Float RW B -273.15…
3.4E+38
245 33/10 0xA150…0xA151/41297…41298
This parameter defines a reference temperature for conversion of the measured mass flow to a volume flow. See also
parameters Capacity Unit and Counter Unit .
Capacity Unit Type Pressure
Type Access Range FlowDDE FLOW-BUS Modbus
Float RW B 0…3.4E+38 246 33/11 0xA158…0xA159/41305…41306
This parameter defines a reference pressure for conversion of the measured mass flow to a volume flow. See also
parameters Capacity Unit and Counter Unit .
4.7.1 Advanced fluid set parameters
Note that the parameters described in this section do not contain any actual measurement values, but only fixed reference
values, which can be used for capacity calculations, etc.