background image

4

bromic.com/heat

IMPORTANT NOTES AND WARNINGS

WARNING

• THIS APPLIANCE SHALL NOT BE INSTALLED OR USED 

  IN RESIDENTIAL DOMESTIC INDOOR AREAS
•  CHILDREN AND ADULTS SHOULD BE ALERTED TO THE
  HAZARDS OF HIGH SURFACE TEMPERATURES AND
  SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING
 IGNITION
•  YOUNG CHILDREN SHOULD BE CAREFULLY
  SUPERVISED WHEN THEY ARE IN THE AREA OF THE
 HEATER
•  DO NOT USE OR STORE FLAMMABLE MATERIALS
  NEAR THIS APPLIANCE
•  CLOTHING OR FLAMMABLE MATERIALS SHOULD NOT
  BE HUNG FROM THE HEATER OR PLACED ON OR
  NEAR THE HEATER
•  DO NOT SPRAY AEROSOLS OR FLAMMABLE MATERIALS
  IN THE VACINITY OF THIS APPLIANCE WHILE IT IS IN
 OPERATION
•  ANY GUARD OR OTHER PROTECTIVE DEVICE
  REMOVED FOR SERVICING THE HEATER (CONDUCTED BY
  AN AUTHORIZED PERSON) MUST BE REPLACED PRIOR TO
  OPERATING THE HEATER
•  INSTALLATION AND REPAIR SHOULD BE DONE BY A
  QUALIFIED SERVICE PERSON. THE HEATER SHOULD
  BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY
  BY A QUALIFIED SERVICE PERSON
Failure to follow the warnings and instructions in this manual 

could result in severe personal injury, death or property damage.

• 

This Installation, Operation and Service manual should not 

be removed from the site of installation.

• 

Installer should leave manual with the customer for future 

reference.

• 

This Appliance is approved FOR OUTDOOR OR AMPLY 

VENTILATED AREA USE. (see attached diagrammatical 

representations of outdoor areas “Appendix A”) and for 

NON DOMESTIC INDOOR APPLICATION.

• 

Do not perform maintenance until heater has been turned 

off, power disconnected, and heater temperature has 

cooled to room temperature.

• 

Do not expose the burner to water or moisture.  

THE APPLIANCE IS TO BE PROTECTED FROM RAIN.

• 

Do not use the heater if any of these parts are exposed 

to water until the appliance is inspected or repaired by an 

authorised service person.

• 

The installer is to ensure that the requirements of the local 

authority, local gas fitting regulations, municipal building 

codes, and any other relevant statutory regulations are 

carried out.

• 

Certain materials or items, when stored under or near the 

appliance, will be subjected to radiant heat and could be 

seriously damaged. Ensure combustible materials eg. 

overhead structures, walls, floors, furniture, fixtures and 

plants must be kept 1100mm from the top and side.

• 

The whole gas system, hose assembly, regulator, pipes, and 

burner should be inspected for damage and leaks before 

use and at least annually by an authorized person for the 

life of the heater.

• 

All leak tests should be done with a soap solution. Never 

use an open flame to check for leaks.

• 

Do not use the heater until all connections have been leak 

tested by an authorised person.

• 

Inspect the hose assembly before each use of the appliance.

• 

The hose assembly must be replaced prior to the appliance 

being put into operation if there is evidence of excessive 

abrasion or wear, or if the hose is damaged.

• 

The replacement hose assembly must be AGA approved.

• 

The hose assembly is not to be located in areas where the 

hose may be subject to accidental damage.

• 

This radiant heater is NOT intended to be installed on 

recreational vehicles and/or boats.

• 

Repair to be carried out ONLY by an authorised person.

• 

Improper installation, adjustment, or alteration can cause 

personal injury, property damage, or even death.

• 

Do not attempt to alter the unit in any manner.

• 

Remove transit protection before use.

• 

Never operate the heater in an explosive environment such 

as areas where petrol or other flammable liquids or vapours 

are stored.

• 

Turn off the gas supply immediately if smell of gas is 

detected.

• 

Do not paint any surface of the heater.

• 

Do not throw objects at Glass facia.

• 

The facia breaks, discontinue use, disconnect power and 

gas and isolate area affected by breakage.

• 

Control compartment, burner and circulation air 

passageways of the heater must be kept clean. Frequent 

cleaning may be required as necessary.

• 

Turn Gas Supply off when not in use.

• 

Check the heater immediately if any of the following occurs:

 

»

The heater does not reach temperature.

 

»

The burner makes popping noise during use (a 

slight noise is normal when the burner is ignited or 

extinguished).

• 

This appliance can be used by children aged from 8 years 

and above and persons with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge if 

they have been given supervision or instruction concerning 

use of the appliance in a safe way and understand the 

hazards involved. Children shall not play with the appliance. 

Cleaning and user maintenance shall not made by children 

without supervision.

• 

Check for damage to the appliance regularly. If damage to 

the cord, plug or appliance is suspected, discontinue use 

immediately and contact the supplier or qualified person 

for repair.

• 

If the supply cord and plug is damaged, It must be replaced 

by the manufacturer, its service agent or similarly qualified 

persons in order to avoid hazard.

• 

Avoid inhaling fumes emitted from the heater’s first 

use. Smoke and odour from the burning of oils used in 

manufacturing will appear. Both the smoke and odour will 

dissipate after approximately 30 minutes.

• 

Ensure that a watertight seal is maintained on the electrical 

control box at all times

• 

Regularly check for damage to the rubber seals. If damage to 

the rubber seals is suspected, discontinue use immediately, 

switch off power and contact the place of purchase or 

authorized service technician for repair.

• 

The heater is not located immediately below a socket outlet

• 

The appliance shall, under no circumstances, be covered 

with insulating material or similar material.

• 

Fire Sprinklers must be located at an appropriate distance 

from each heater to avoid accidental activation of the 

sprinkler. Ethylene glycol or propylene glycol must never be 

used in fire sprinkler systems where heaters are present as 

these substances maybe become flammable when heated. 

A fire sprinkler professional must be consulted when heaters 

are installed where fire sprinklers are present to ensure that 

heaters and the fire sprinkler system are properly integrated.

!

Содержание PLATINUM 300 SMART-HEAT



























Отзывы: