Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 39

Страница: 39 / 119

Attaching the extensions to the front of the device

Complete the following steps to attach the extension brackets to the front of the device. There are medium and long extension brackets
that you can use for this step. Choose the correct extension for the depth of your rack.

Select the proper length extension bracket for your rack depth.

2. Position the right extension along the side of the device as shown in

Figure 22

3. Attach the bracket using four 8-32 x 5/16-in. flathead screws.
4. Repeat

Step 1

and

Step 2

to attach the left front extension to the left side of the device.

5. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 22 Attaching the bracket extensions to the device

Extension brackets

Screws, 8-32 x 5/16-in., flathead Phillips

Installing the device in the rack

Complete the following steps to install the device in the rack.

Position the device in the rack, as shown in

Figure 23

, providing temporary support under the device until the rail kit is secured

to the rack.

2. Attach the right front bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use

the upper and lower holes in the bracket.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды