Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 176

background image

Application and Encryption Blades

●

Introduction................................................................................................................... 127

●

FS8-18 blade.................................................................................................................127

●

FX8-24 blade.................................................................................................................127

●

FCOE10-24 blade......................................................................................................... 129

Introduction

This appendix provides details about the application and encryption blades that are available optionally
for the Brocade DCX 8510-8. Contact your Brocade DCX 8510-8 supplier for additional information.

FS8-18 blade

The FS8-18 encryption blade is a high performance 16-port autosensing blade with data cryptographic
(encryption/decryption) and data compression capabilities designed for enterprises to secure their data
against theft or unauthorized use and to compress tape data for maximum utilization of tape media. The
encryption blade is a network-based solution that secures data-at-rest for heterogeneous tape drives,
disk array LUNs, and virtual tape libraries.

The FS8-18 blade provides the following major features:

• 16 autosensing F_Ports, FL_Ports, E_Ports, EX_Ports, and M_Ports
• 16 SFP media interfaces
• Encryption engines
• Key management/generation
• Key management with these hardware interfaces:

‐

Two 1000Base copper type media interfaces

‐

One smart card interface

• Security supervisor tamper detection and response capability
• Common Criteria (CC) EAL-3 compliant

FX8-24 blade

The FX8-24 blade has 12 external Fibre Channel (FC) SFP ports supporting the Fibre Channel Routing
Services and 10 external 1 Gigabit Ethernet (GbE or GE) SFP ports supporting the Fibre Channel Over
IP (FCIP) feature. There are also 2 licensable external 10 Gigabit Ethernet (10 GbE or 10 GE) SFP
ports supporting FCIP. It operates with the Brocade Fabric Operating System and can communicate
with another FX8-24 or a Brocade 7800 for both Fibre Channel Routing Services and FCIP, or a
Brocade AP7420 for Fibre Channel Routing Services. The GbE ports on the FX8-24 are not compatible
with the GbE ports on the FR4-18i blade, the Brocade 7500 switch, and the Brocade 7840 switch.

Brocade DCX 8510-8 Backbone Hardware Reference Manual

127

53-1002180-08

«
...
125
126
127
128
129
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

Univerge SV8100

Бренд: NEC Страницы: 2

Бренд: Acano Страницы: 17

Бренд: U.S. Converters Страницы: 5

Бренд: 7starlake Страницы: 32

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

S7000FC4UR - Server System - 0 MB RAM

Бренд: Intel Страницы: 13

Бренд: Lenovo Страницы: 14

ThinkSystem SR850 V2

Бренд: Lenovo Страницы: 288

IdeaCentre 3013

Бренд: Lenovo Страницы: 1

Бренд: Lenovo Страницы: 24

System x3550 M5

Бренд: Lenovo Страницы: 59

Бренд: Lenovo Страницы: 54

ThinkAgile VX2320

Бренд: Lenovo Страницы: 108

IdeaCentre D400

Бренд: Lenovo Страницы: 43

Flex System x240 M5

Бренд: Lenovo Страницы: 40

System x3250 M5

Бренд: Lenovo Страницы: 51

Бренд: Lenovo Страницы: 44

Secure Managed Client Storage Array

Бренд: Lenovo Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды