background image

Brocade 6520 Hardware Reference Manual

7

53-1002705-01

Installation and safety considerations

2

DRAFT: BROCADE CONFIDENTIAL

The ambient air temperature does not exceed 40

°

 C (104

°

 F) while the switch is operating.

Table 2

 lists the acceptable environmental ranges for both operating and nonoperating (such as 

during transportation or storage) conditions.

Rack considerations

For successful installation and operation of the switch in a rack, ensure the following rack 
requirements are met:

The rack must be a standard EIA rack.

A rack space that is two rack units (2U) high; 8.90 cm (3.50 inches) high and 48.3 cm (19 
inches) wide.

The equipment in the rack is grounded through a reliable branch circuit connection and 
maintain ground at all times. Do not rely on a secondary connection to a branch circuit, 
such as a power strip.

Airflow and temperature requirements are met on an ongoing basis, particularly if the 
switch is installed in a closed or multirack assembly.

The additional weight of the switch does not exceed the rack’s weight limits or unbalance 
the rack in any way.

The rack is secured to ensure stability in case of unexpected movement, such as an 
earthquake.

Recommendations for cable management

The minimum bend radius for a 50 micron cable is 2 inches under full tensile load and 1.2 inches 
with no tensile load. 

Cables can be organized and managed in a variety of ways, for example, using cable channels on 
the sides of the rack or patch panels to minimize cable management. Following is a list of 
recommendations:

TABLE 2

Environmental requirements

Condition

Acceptable during operation

Acceptable During Non-Operation

Ambient 
Temperature

0º to 40º C (32º to 104º F)

-25º to 70º C (-13º to 158º F)

Humidity

10% to 85% RH non-condensing, at 
40º C (104º F)

10% to 90% RH non-condensing, at 70º C 
(158º F)

Altitude

0 to 3 km (9,842 feet) above sea level

0 to 12 km (39,370 feet) above sea level

Shock

20 G, 6 ms, half-sine wave

33 G, 11 ms, half-sine wave, 3/eg Axis

Vibration

0.5 G sine, 0.4 gms random, 5-500 Hz

2.0 G sine, 1.1 gms random, 5-500 Hz

Air flow

Maximum - 186.89 cmh (110 cfm)

Nominal - ??.?? cmh (?? cfm)

NOTE: Airflow can be Forward or Reverse 
depending on purchased option

NA

Heat dissipation

843.03 BTU/hr (no optics configuration)
1556.36 BTU/hr (fully populated port 
configuration)

NA

Содержание Brocade 6520





























































Отзывы: