background image

4

2. C

ONTROLS

This unit is equipped with an integrated control located 
under the electrical compartment of the unit. Use the push 
button (

1

) to control the unit; the LED (

2

) will then show 

which mode the unit is in (see illustration at right and table 
below).

 

2.1 B

OOTING

 S

EQUENCE

The unit booting sequence is similar to a personal computer boot sequence. Each time 
the unit is plugged after being unplugged, or after a power failure, the unit will perform a 
30-second booting sequence before starting to operate.

During the booting sequence, the integrated defrost control LED will light AMBER for 
5 seconds, and then will shut off for 2 seconds. After that, the LED will light RED for 
the rest of the booting sequence. During this RED light phase, the unit is checking and 
resetting the motorized damper position. Once the motorized damper position completely
set, the RED light turns off and the booting sequence is done. 

NOTE: No command will be taken until the unit is fully booted.

NOTE: The integrated control 

must be turned OFF

 to use an optional main control.

If a problem occurs during the unit operation, its integrated control LED (

2

) will blink. The color 

of the blinking light depends on the type of error detected. Refer to Section 4 Troubleshooting 
on last page for further details.

1

2

VD0310

LED C

OLOR

R

ESULTS

AMBER

U

NIT

 

IS

 

ON

 L

OW

 S

PEED

GREEN

U

NIT

 

IS

 

ON

 H

IGH

 S

PEED

N

O

 

LIGHT

U

NIT

 

IS

 O

FF

 

OR

 

CONTROLLED

 

BY

 

A

 

MAIN

 

CONTROL

 

2.2 O

PTIONAL

 M

AIN

 

AND

 A

UXILIARY

 C

ONTROLS

For more convenience, this unit can also be controlled using an optional main wall 
control. Many models can be used, but only one main wall control can be connected to 
the unit.

NOTES:  1.  The integrated control 

must be turned OFF 

to use an optional main control.

 

2.  If an optional auxiliary control is used, if activated, the operation of this 

auxiliary control will override the optional main control operation.

For more information about the available controls and their operation modes, refer to the 

Main and auxiliary wall control User Guide

 (included with the ventilation unit and also 

available at www.broan.com).

Содержание ERVH100S

















Отзывы: