Broadway Limited Paragon 2 Series страница 21 Скачать руководство пользователя

Страница: 21 / 28

Paragon 2

The motor movement can be delayed after turning

the throttle to allow the engine sound to rev up before

movement. To enable this feature, set CV 245 to 18 or

19. Set back to 16 or 17 to disable. Once enabled, the

delay can be adjusted by setting CV 248.

CV2, 6 and 5 control the motor start, mid range and

maximum voltages. The possible values are from 0 to

255. 0 would cause the motor voltage to be 0 and 255

would cause it to be 100 % on. These can be used to

adjust 2 different locomotives to start and run at the

same speeds. Usually the back EMF must be turned off

on one or all of the engines to enable different types of

engines to run together smoothly.

CV95 is the Forward/Reverse Trim, used to make the

forward and reverse speed match if they are different.

Setting the value from 1-127 makes the engine run

slower in reverse. 1 is the slowest. Setting CV95 from

129 to 255 makes it run faster in reverse. 255 is the

fastest. A value of 0 or 128 disables the feature.

CV2 is the start voltage, and determines the motor

voltage at speed step 1. If back EMF is disabled, this

value must be high enough to get the engine moving.

CV6 is the motor voltage at the middle speed step. It

must be greater than CV2 and less than CV5.

CV5 is the motor voltage at the highest speed step.

CV3 sets the acceleration rate. Its range is from 0 to

255. Setting to 20 makes the engine take an additional

20 seconds to accelerate from stopped to full speed.

CV4 sets the deceleration rate. Its range is from 0 to

255. Setting to 20 makes the engine take an additional

20 seconds to decelerate from full speed to stopped.

Speed Table

: If setting CV2, 5, and 6 is not sufficient

to make 2 engines run together through the entire speed

range, the speed at each step can be set using CV’s

67 through 94. To use these values, CV29, bit 4 must

equal 1. See Paragon 2 Technical Reference Manual for

specifics. This should only be attempted by experienced

users.

Содержание Paragon 2 Series





























Результаты поиска

Содержание Paragon 2 Series

Отзывы:

Похожие инструкции для Paragon 2 Series

Бренды по названию

Популярные бренды

Broadway Limited Paragon 2 Series, Руководство оператора

Результаты поиска

Содержание Paragon 2 Series

Отзывы:

Похожие инструкции для Paragon 2 Series

Бренды по названию

Популярные бренды