Broadcast Tools Site Sentinel 4 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 45

Broadcast Tools Site Sentinel 4 Скачать руководство пользователя страница 10

e-mail:

[email protected]

voice:

360.854.9559

fax:

866.783.1742

10

Site Sentinel™ 4 Installation and Operation Manual

INSTALLATION

Installation

Silence Sensor Inputs

Connect your unbalanced monaural or stereo audio source to the terminals labeled
SSLT, SSRT and AGND. The level should be between -10 and +24 dbu. The input
impedance is approximately 22K ohms. When the SSLT/RT input has audio applied
and the silence sensor is activated, the front panel SS led is illuminated. If the SS led
is out, the signal is too low and if it’s flashing, it is in an alarm condition (if enabled).

TEMPerature Probe Input

Insert the OPTIONAL temperature probe (25 foot cable) mini (3.5mm) plug in to the
rear panel jack labeled “TEMP” -67°F to +257°F (-55°C TO +125°C).

NOTE: Please limit the total length of cable to 50 feet. Please contact the factory
for the proper extension cable. The temperature probe should only be installed or
removed with the power supply disconnected from the Site Sentinel™ 4.

Power Controller Relay

The jumpers are set to provide the relay common (wiper) on the terminal labeled
(PCJP). Please refer to the “Fractional Schematic” in the appendix for more jumper
options.

NETWORK connector

Connect one end of the supplied CAT5 (straight or x-over) cable to the desired ETH-
ERNET (WAN/LAN) port.

PWR 7.5 VDC (Power) connector

Connect the supplied 7.5 volt DC only 1 amp power supply cord in to the Site
Sentinel™ 4’s power jack (center positive) labeled “PWR 7.5 VDC”, then plug the
transformer in to a source of 120 vac 60Hz. Verify that the front panel green
(PWR/HB) power led is illuminated.

Web Setup and Operation

Ethernet “Quick Start” guide

CAUTION! If you are not familiar with Ethernet enabled equipment, it may
be useful to contact your IT department, network administrator or network
consultant for assistance. Assigning an IP address already in use by another
device may cause problems with your network!

Instructions for changing the IP address of the computer that will be used for the
configuration of this product are given here. Note that these instructions are specif-
ically for computers with the Windows XP operating system. For setup using other
operating systems, refer to the appropriate OS user’s manual.

CAUTION!

NEVER DOWNLOAD
FIRMWARE UPDATES
OR CHANGES TO
THE XPORT WEB-
SERVER UNLESS
INSTRUCTED TO DO
SO BY BROADCAST
TOOLS®. DOING SO
DELETES ALL SOFT-
WARE AND VOIDS
ALL WARRANTIES
FROM BROADCAST
TOOLS®, INC.

WEBSITE:

Visit our web site for
product updates and
additional information.

«
...
8
9
10
11
12
...
»

Содержание Site Sentinel 4














































Отзывы:

Нет отзывов