manualshive.com logo in svg

Britpart IIDTOOL, Руководство пользователя

Поделиться
Скачать
Britpart IIDTOOL Скачать руководство пользователя страница 17

17

IIDT

ool

 

Front 

Changes height of only the front axle in all modes. +10mm means the front will be 10mm higher in all 
modes.

 

Rear

Changes height of only the rear axle in all modes. -10mm means the rear will be 10mm lower in all 
modes. 

 Limits

The EAS ECU has internal absolute limits that limit the extent of possible height changes. 
 
For example, if the current calibration is

Sensor

Calibration height value (mm)

Front Left

157

Front Right

138

Rear Left

180

Rear Right 

166

 

And the limits of the EAS ECU are 
 

Sensor

Limit Value (mm)

Upper Front 

200

Upper Rear

200

Lower

No Limits

 
The front can be raised by a maximum of 200 - 157 = 43 mm. The front can be lowered without a 
maximum limit.   
 
The rear can be raised by a maximum of 200 - 180 = 20 mm. The rear can be lowered without a maxi-
mum limit.   

The IIDTool automatically calculates these values and allows only changes within these parameters. 

Note: 

The maximum values for 

lowering

 and 

raising

 are found by trial and error. They will not be 

the same on every vehicle.

GAP Diagnostic 29/01/2013 All right reserved

User manual: V2.17.12, Firmware V2.17.03

Range Rover L322 2002-2005

Содержание IIDTOOL



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды