1.
Pull the grey fabric loop
16
to
pull out both locking arms
17
until
you hear a clicking sound which
indicates they are fully engaged.
2.
Take the Top Tether 14 from the
user guide compartment 15 and
lay it over the child safety seat.
3.
Place the child safety seat facing
in the direction of travel on the
vehicle seat.
4.
Grasp the child safety seat with
both hands and slide the two
locking arms
17
firmly into the
insert guides
02
until the locking
arms engage with a clicking noise
on both sides.
Caution:
The locking arms
are only correctly engaged if
both of the ISOFIX indicators
12
are completely green.
5.
Push the child safety seat with a
substantial amount of force as far
back as it will go.
6.
Shake the child safety seat to
make sure it is safely attached
and re-check to the ISOFIX indi-
cators 12 to make sure that both
of them are completely green
10.
Tension the strap of the Top
Tether 14 until the tension
indicator 27 turns green and the
Top Tether 14 is tightly tensioned.
For the protection of all vehicle occupants
In the case of an emergency stop or an accident, persons or objects which are not properly secured in the car can cause injury to other vehicle
occupants. For this reason, please always check that...
• the backrests of the vehicle seats are locked (e.g. that the latch on a folding rear seat bench is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured in the car via the ISOFIX anchoring and the Top Tether, even when there is no child in the seat
.
For the protection of your child
• The more snugly the harness fits over your child‘s body, the safer your child will be.
• Please do not ever leave your child unattended in the child safety seat in the vehicle.
Preparatory work
1. If your vehicle is not equipped with the ISOFIX insert guides as
standard, clip the two insert guides
02
which are included with the
seat* with the cut-out facing upwards onto the two ISOFIX attach-
ment points
01
of your vehicle.
TIP: The ISOFIX attachment points are located between the surface
and the backrest of the vehicle seat.
2. Move the head restraint on the vehicle seat to the upper position.
* The insert guides make it easier to install the child safety seat with the aid of the ISO-
FIX attachment points and prevent damage to the seat covering. When not in use, they
should be removed and stored in a safe place. On vehicles with a folding backrest the
insert guides must be removed before the backrest is folded.
Any problems which occur are usually caused by dirt or foreign objects on the insert
guides and on the hooks. Clean off any dirt or foreign objects to remedy this type of
problem.
7.
Take the Top Tether 14 and press
the metal tongue 28 away from
the strap to lengthen the strap and
pull the Top Tether 14 by the snap
hook 26 until it makes a V-shape.
8.
Guide the Top Tether
14
on the
left and right-hand sides past the
headrest.
9.
Hook the snap hook 26 into the
Top Tether anchoring point recom-
mended in your vehicle owner‘s
guide.
13
. Pull the shoulder straps 07 to
one side and put the two buckle
latches 21 into the harness
retainer 04
14.
Make sure that the buckle 05 is
folded forwards and place your
child in the child safety seat.
15.
Put the shoulder straps 07 over
the shoulders of your child.
Caution:
The shoulder straps
07
must not be twisted or
swapped.
Caution:
Check that the child
safety seat is correctly
attached
11.
Press the adjusting button 08
and at the same time pull both
shoulder straps 07 forwards.
Caution: Do not pull on the shoul-
der pads 06 .
12.
Open the harness buckle 05
(press the red button).
• Use on the rear seat:
Move the front seat forward far enough that you child‘s feet cannot hit the backrest of the front seat (to prevent risk of injury).
• The child safety seat can get hot in direct sunshine. Caution: Children‘s skin is delicate and could be injured as a result. Protect the child
seat against intensive direct sunlight when it is not currently in use.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Make stops during longer journeys to give your child an opportunity to run about and play.
To protect your vehicle
Some vehicle seat coverings made of more delicate materials (e.g. velour, leather, etc.) may develop wear marks when child seats
are used. For optimum protection of your seat covers, we recommend using the BRITAX RÖMER Car Seat Protector, which is
available from our range of accessories.
20.
Pull on the adjusting strap 09
until the harness lies flat and
is close against your child‘s
body.
Caution:
Pull out the
adjusting strap to the front.
Caution:
The hip straps
28
must be positioned as
low as possible over your
child‘s hips.
19.
Guide the two buckle latches
21
together and engage them before
putting them into the harness
buckle 05 - this should make a
clicking noise.
A correctly adjusted headrest 03
ensures optimal protection for your
child in the safety seat:
The headrest 03 must be adjusted
so that the shoulder straps 07 are at
the same level as your child’s shoul-
ders or slightly above.
17.
Pull the adjusting ring of the head
rest 13 upwards
18.
Move the head rest 03 to the
correct shoulder strap height and
check that it is properly engaged
by lightly sliding the head rest 03
downwards.
For the safety of your child, before every journey in the car check that...
• the child safety seat is engaged on both sides with the ISOFIX locking arms
17
in the ISOFIX attachment points
01
and that both ISOFIX
indicators
12
are completely green;
• the child safety seat is securely fastened;
• the Top Tether
14
is tightly tensioned over the backrest of the car seat and the tension indicator
27
is green;
• the straps of the child safety seat are close to the body without constricting the child;
• the shoulder straps
07
are correctly adjusted and the straps are not twisted;
• the shoulder pads
06
are in the right position on your child‘s body;
• the buckle latches
21
are engaged in the harness buckle
05
.
Caution:
If your child attempts to open the grey ISOFIX locking buttons
11
or the harness buckle
05
, make sure to stop at the
earliest opportunity. Check that the child safety seat is correctly attached and make sure that your child is properly secured. Teach
your child about the dangers involved.
Removing the child safety seat with ISOFIX
1.
Loosen the Top Tether
14
2.
Unhook the snap hook
26
from the anchoring point and lay the Top Tether
14
to the front over the child safety seat
3.
Press on the grey ISOFIX unlocking buttons on the left and right-hand side of the seat shell
18
.
The ISOFIX locking arms
17
will release and the two ISOFIX indicators
12
will change colour to red.
4.
Pull the seat forwards and stow the Top Tether
14
back in the user guide compartment
15
.
5.
Slide the ISOFIX locking arms
17
back into the seat shell
18
A rattling noise is produced when the locking arms are pushed back in.
TIP: The locking arms are protected against damage when they are pushed back into the seat base.
Caution:
Remove the child safety seat from the vehicle.The child safety seat must never be transported in the car if it is not properly secured.
INSTALLATION
Take the time to carefully read through these instructions, and always keep them ready to hand in the designated pocket on the child seat.
click!
click!
02
01
H
1 cm
14
27
H
07
08
06
I
14
28
26
E
16 17
14
15
12
12
14
04
21
07
03
03
13
21
05
09
28
A
B
C
D
F
N
M
L
K
J
G
05
140828_User_guide_TRIFIX_GB.indd 2
28.08.2014 14:33:44
