2
5
Identify the
required position of
the valve and prepare
the water supply pipes.
Supply pipes should be
150mm apart.
Using the backplate
supplied with the
wallmount, mark and
drill holes.
Secure the isolator
Secure the isolator
onto the backplate
onto the backplate
ensuring the olive is
ensuring the olive is
positioned over the
positioned over the
pipework correctly.
pipework correctly.
Push shrouds to the
Push shrouds to the
back of the wall outlet,
back of the wall outlet,
securing them against
securing them against
the rubber fixing plate
the rubber fixing plate
4
3
1
Installation
150mm C
entr
es
Rotate the shroud until
Rotate the shroud until
the opening aligns with
the opening aligns with
the isolation screw.
the isolation screw.
Turn the screw to isolate
Turn the screw to isolate
the water. Reverse the
the water. Reverse the
process when turning
process when turning
the water back on.
the water back on.
1
Isolation
2
Remove the concealing
Remove the concealing
cap from the shroud.
cap from the shroud.
Secure the rubber backplate
Secure the rubber backplate
and backplate into place.
and backplate into place.
Insert filter washer and
Insert filter washer and
secure the shower to
secure the shower to
the wall mount.
the wall mount.
21mm
21mm
REMEMBER
To service
your
product!
Operation
REMEMBER
hot on the left,
cold on the
right
Pack Contents
Installation Instructions
& User Guide
Please leave these instructions
with the end user
Product Codes: AR2 SHXMTFF C (D3)
AR2 SHXVOFF C (D3)
All products manufactured and supplied by Bristan are safe to use provided that
they are installed, operated and receive regular maintenance in
accordance with these instructions.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
current by-laws. For full Installation Requirements & Notes (IRN) please
visit
wras.co.uk/directory.
Isolation valves must be fitted to the inlet water supplies to ensure ease of future
maintenance.
Before installing this product the water supply must be thoroughly flushed in
order to remove any swarf, solder etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Full access must be made available for future maintenance/servicing purposes.
Before drilling into walls, check that there are no hidden electrical wires,
cables or water supply pipes. This can be checked with the aid of an
electronic detector.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
If in doubt, contact a registered plumber or your Local Water Authority or
the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: 01708 472791
Prior to Installation
Hot
Hot
Cold
Cold
On
On
Off
Off
Supplied
with
AR2 SHXMTFF C
only
x1
x1
x2
x2
x2
x2
x8
x8
x2
x1
x1
x1
x1
x2
x2
x4
x4
x1
IMPORTANT
150mm
Centres
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0
3.0
60°C
65°C
Specifications
Maximum Static Pressure:
10.0 bar
Inlet Water Temperature
15mm
Compression
Inlet Connections
Min:
0.2 bar
Max:
5.0 bar
Working Pressures
The inlet hot water must
be at least 10°C above the
required blend temperature.
HP-S & LP-SE
Factory
pre-set 38°C
TMV2 Designation
Inlet Dimensions
5°C
25°C
Cold Water Supply
Min:
5°C
Max:
25°C
Hot Water Supply
60-65°C Recommended
Tools You’ll Need
Flat head Screwdriver
Cross head Screwdriver
Hexagonal Keys
Pipe Cutter
Pencil
Drill
Spanner
