2
3
4
8
9
10
Specifications
Delete Sensor
Transmission/Detection
7
Pairing Channels
Multiple Sensors
MAS200
90° (Horizontal)
Centerline: 13 ft (4 m)
Side: 5 ft (1.5 m)
32 ft (10 m)
1 CR2450 battery (included)
Approx. 28,000 triggers
SHC1000, SHC1000W
Door Knocker Casing:
2.3" x 3.8” x 1.1” ( 59 x 97 x 28 mm)
Motion Sensor Unit:
1.7" x 2” x 0.5” ( 44 x 52 x 14 mm)
Receiver Unit:
1.5" x 1.1” x 0.2” ( 37 x 29 x 6 mm)
Door Knocker Casing:
1.3 oz ( 36 g)
Motion Sensor Unit:
0.7 oz ( 21 g) (without batteries)
Receiver Unit:
0.2 oz ( 5.5 g)
Door knocker casing, Motion sensor unit
(inside knocker casing), Receiver unit,
Magnetic wall mount, Battery lock,
Screwdriver, 1 CR2450 battery.
Model
Detection Angle
IPX4
Splash-proof
Detection Distance
Transmission Distance
to Receiver
Power Source
Battery Life
32 ˚F ~ 113 ˚F (0˚C ~ 45˚C)
Operating
Temperature
Compatible Model
Size (WxHxD)
Weight
Package Contents
Transmission Distance:
32 ft (10m)
between motion sensor unit and receiver
unit inside the camera. When you choose Portable
Mode, make sure the two units are within the transmis-
sion distance.
Sensor Detection Area:
Detection angle:
90 degrees
(Horizontal).
Detection distance:
13 ft (4 m)
(Centerline).
(Approx.
5 ft (1.5 m)
on both sides of the centerline).
One camera supports up to 6 motion sensors. You
make different channel combinations to identify each
unique motion sensor.
Motion Sensor Pairing Channel Switch:
Pairing Channel Combination:
ON
1
2
3
Channel 1:
ON
1
2
3
Channel 4:
ON
1
2
3
Channel 5:
ON
1
2
3
Channel 6:
ON
1
2
3
Channel 2:
ON
1
2
3
Channel 3:
3. Pair sensors.
Pin the pairing button
for 6 secs.
(Place the
motion sensor within
12 in (30cm)).
On motion sensor, LED
light flashes blue.
On receiver unit, LED light
flashes red.
On camera screen,
motion sensor icon
appears.
1
2 3
4 5 6
1
6 secs
10 m
(32 ft)
1. Motion Sensor takes around 30 secs to warm up
after sensor pairing is done.
2. Run motion sensor test and make sure the
camera is working properly.
www.brinno.com/support/registration
For manuals in other languages, visit
www.brinno.com/support
The product features, specifications sheets and instructions may
differ from actual products. Please refer to Brinno official site for
the latest version of user manual.
ON
1
2
3
Channel 1 (Default):
Time
2013/05/01
17:30
Set
Exit
Press to Exit
Delete Sensor
Sensor 1
Delet all
Exit
Time
2013/05/01
17:30
Set
Exit
Press to Confirm
CONFIRM: Delete
Sensor 1?
Yes
No
Press to Setup
Paired Motion Sensor
Sensor 1
1. The screen displays all paired sensors.
2. Select one sensor or all sensors to be deleted from
the list.
3. Press
SHUTTER BUTTON
again to delete.
Press
SHUTTER
BUTTON
to go to
the
DELETE SENSOR
option.
Press
SHUTTER
BUTTON
to confirm
deletion.
4. Restart the camera. The selected sensor will be
permanently deleted.
1. Insert receiver unit into camera.
2. Turn the camera power on.
BSMI 有電池產品
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理使用過之電池。
FCC
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT.
This equipment has been tested and found to comply with the limit s for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
theuser is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NCC LP0002
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更
頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應
改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻
電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts
de licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage adioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause undesired
operation of the device.
1.5 m
(5 ft)
1.5 m
(5 ft)
90°
4 m
(13 ft)
