Brinly LS2-42BH-G Скачать руководство пользователя страница 9

Страница: 9 / 28

================================================================================================

1019383-A

ASSEMBLY

Step 5

First

Second

Last

Step 6

Note: Wheel assembly

not shown for clarity.

FIRST

- Run Bolt (27) through the

Left Tow Bar (4) using the following hardware

from

PANEL

in the order listed below:

• Hex Bolt (27)

• 5/16” Washer (19)

• Left Tow Bar (4)

• 5/16” Washer (19)

• 5/16” Lock Washer (18)

• 5/16 Hex Nut (16)

TIGHTEN HARDWARE SECURELY

SECOND -

Adding on to the same bolt (27), attach the Lock

Arm (1) using hardware in this order:

• Hex Bolt (27)

• 5/16” Washer (19)

• Lock Arm (1)

• 5/16” Washer (19) and Nylon Lock Nut (25)

Note:

Do not over tighten the Nylon Lock Nut

(25). The Lock Arm (1) should be able to pivot freely after assembly.

LAST

- Slide the Vinyl Bolt Cap (7) over the end of the Bolt (27).

Loosely add the Bolt (13) &

Lock Nut (21) from

PANEL 04

to the Height Adjustment

Handle (2).

Pointing the Nut side out, slide the

Height Adjustment Handle (2) into

place against the Lower Pivot (43)

side plate.

Use the head of Bolt 13
to hold in place.

TIGHTEN HARDWARE SECURELY.

NOTE: The large hole

in bottom of the Height

Adjustment Handle (2) must fit over the Tube

extending past the Lower Pivot (43) side plate.

Содержание LS2-42BH-G





























Результаты поиска

Содержание LS2-42BH-G

Отзывы:

Бренды по названию

Популярные бренды

Brinly LS2-42BH-G, Руководство пользователя

Результаты поиска

Содержание LS2-42BH-G

Отзывы:

Бренды по названию

Популярные бренды