Quick Setup Guide
Pressure Washer
Unpack pressure washer
1. Remove everything from carton except pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly.
If items are damaged or missing, call
1-800-743-4115
.
4. Prior to assembly, lubricate all o-ring connections as described in
operator’s manual.
Assemble pressure washer
1. Place handle (A) onto handle supports connected to main unit. Make
sure holes in handle align with holes on handle supports.
1
NOTICE
It may be necessary to move the handle supports from side to
side in order to align the handle so it will slide over the handle supports.
2. Place cleaning tank (B) over holes on handle and handle supports
(viewing from rear of unit).
2
3. Insert carriage bolts (C) through top holes of the handle, handle
supports and cleaning tank (B) from front of unit and attach a plastic
knob (D) from rear of unit. Tighten by hand.
2
4. Push tree clips (E) into bottom holes of cleaning tank and holes on
handle supports until they sit flat against cleaning tank.
3
5. Place accessory tray (F) over holes on handle (A) (viewing from
front of unit). Push the tree clips (E) into the holes until they sit flat
against the accessory tray.
4
6. Insert “L” bolt (G) through hole just below billboard on right side of
handle (viewing from front of unit). Hold “L” bolt in place and attach a
plastic knob (D) from inside of unit. Tighten by hand.
5
Attach detergent siphon hose to pump
1. Attach detergent siphon hose (H) to barbed hose fitting (J) on pump.
6
Add engine oil and fuel
NOTICE
You MUST properly fill engine with oil before attempting to start
pressure washer.
NOTICE
DO NOT use E85 fuel.
NOTICE
DO NOT mix oil with fuel.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove oil fill cap/dipstick ( ).
7
3. Using oil funnel (optional), slowly pour contents of supplied oil into
oil fill opening, frequently checking oil level. DO NOT OVERFILL.
8
4. Replace and fully tighten oil fill cap/dipstick.
5. Clean area around the fuel cap ( ), remove fuel cap.
7
6. Slowly add regular unleaded fuel to bottom of fuel level limit in neck
of fuel tank. Be careful not to overfill.
9
7. Replace fuel cap. Let any spilled fuel evaporate before starting
engine.
Move pressure washer
to safe operating location
1. Move pressure washer outdoors to a flat, level surface.
2. Running engines give off carbon monoxide. Keep at least 5 ft.
(1.5 m) clearance on all sides of pressure washer including overhead
to reduce the risk of exhaust heat or exhaust gases igniting nearby
combustible material.
10
Connect spray gun
NOTICE
Remove and discard the shipping caps from the pump’s high
pressure outlet and water inlet before attaching hoses
1. Uncoil high pressure hose (K) and attach one end of hose to base of
spray gun (L). Tighten by hand.
11
2. Attach other end of high pressure hose (K) to high pressure outlet
(M) on pump. Tighten by hand.
12
Connect water supply
1. Before connecting garden hose to water inlet, inspect inlet
screen (N).
13
NOTICE
If inlet screen is damaged or missing, DO NOT use pressure
washer, call
1-800-743-4115
.
2. Clean screen if it contains debris or have it replaced if damaged.
3. Run cold water through garden hose for 30 seconds to clean out any
debris. Garden hose length must not exceed 50 ft. (15 m). Turn off
water supply and attach garden hose (P) to water inlet (Q). Tighten
by hand.
13
Start pressure washer
NOTICE
You MUST connect and turn on water supply fully before
starting engine.
1. Put on safety goggles.
2. Turn on water supply.
3. Push red button (R) on spray gun and pull trigger until water comes
out in a steady stream.
14
4. Place colored spray tips (S) in slots on holder that’s attached to
nozzle extention.
15
5. Attach nozzle extention (T) to spray gun (L).
16
6. Choose desired quick-connect spray tip (S), pull back on collar of
nozzle extention (T). Insert spray tip and release collar. Tug on spray
tip to make sure it is securely in place.
17
7. Pull choke rod (U) to “Closed” position.
18
8. Move engine stop switch (V) to “On” position.
18
9. When starting engine, position yourself as recommended and grasp
starter grip handle and pull slowly until you feel some resistance.
Then pull rapidly to start engine.
19
10. After each starting attempt, where engine fails to run, always point
gun in safe direction, press red button and squeeze spray gun trigger
to release high pressure.
NOTICE
When engine starts, slowly move choke rod to “Open” position
as engine warms. If engine falters, move choke rod to “Closed” position,
then to “Open” position.
11. Point spray gun toward surface to be cleaned, push red button and
pull trigger to begin spraying.
Stop pressure washer
1. Let engine idle for 2 minutes.
2. Move engine stop switch (V) to “Off” position.
18
3. Turn off water supply.
4. Point spray gun in safe direction, press red button, and squeeze
spray gun trigger to relieve retained high water pressure.
5. Disconnect garden hose from pump.
6. Disconnect high pressure hose from pump and gun for storage. For
long term storage instructions, see operator’s manual.
7. Remove safety goggles.
Items Included:
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free
1-800-743-4115
or visit our website,
BRIGGSandSTRATTON.COM
Operator’s and Engine Manuals
(not shown)
WARNING
Failure to read and follow the operator’s
manual and all operating instructions could
result in death, serious injury, and/or property
damage.
WARNING
Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death,
serious injury and/or property damage. Turn
pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Let spilled fuel
evaporate before starting engine. Always allow space for
fuel expansion.
WARNING
Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting
in serious injury. NEVER pull starter cord without first
relieving spray gun pressure. Pull starter cord slowly
until resistance is felt, then pull rapidly. Firmly grasp
spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
WARNING
Running engine gives off carbon
monoxide, an odorless, colorless, poison
gas. Breathing carbon monoxide could result
in death, serious injury, nausea or fainting.
Operate this product ONLY outdoors. DO NOT operate
this product inside any building or enclosure, even if
windows and doors are open.
WARNING
High water pressure could cut through
skin resulting in serious injury. Spray gun
traps high water pressure, even when engine
is stopped and water is disconnected. NEVER
aim spray gun at people, animals, or plants. ALWAYS
point spray gun in safe direction, press red button and
squeeze spray gun trigger to release high pressure,
every time you stop engine.
WARNING
Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
You will need:
• Utility knife • Unleaded fuel • Garden hose, 50 ft. (15 m) or less • Safety goggles (indirect vented type)
© 2012 Briggs & Stratton Corporation. All rights reserved. Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
This pressure washer is rated in accordance to the Pressure Washer Manufactures Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas. Breathing carbon
monoxide could result in death, serious injury, nausea or
fainting. Operate this product ONLY outdoors. DO NOT
operate this product inside any building or enclosure, even if windows
and doors are open.
9
7
8
Exhaust Port
Pointed away from
dwelling openings
10
11
K
L
12
M
K
14
R
13
N
P
Q
A
B
D
C
E
A
E
F
D
G
H
J
6
5
4
3
2
1
S
15
16
17
18
19
T
L
S
T
U
V
WARNING
Risk of eye injury. Spray could splash back or propel
objects resulting in serious injury. Always wear indirect
vented (chemical splash) safety goggles marked to
comply with ANSI Z87.1 when using or in vicinity of this
equipment. NEVER substitute safety glasses or dry-condition goggles
for indirect vented safety goggles.
WARNING
Starter cord kickback (rapid retraction) will pull hand
and arm toward engine faster than you can let go which
could cause broken bones, fractures, bruises, or sprains
resulting in serious injury. NEVER pull starter cord without
first relieving spray gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Firmly grasp spray gun with both
hands when using high pressure spray to avoid injury when spray gun
kicks back.
Not
for
Reproduction
