background image

Generac Portable Products 3250 Watt Generator

11

SPECIFICATIONS

Maximum Surge Watts  . . . . . . . . . . . . . . . 4,550 Watts

Continuous Wattage Capacity  . . . . . . . . . 3,250 Watts

Power Factor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0

Rated Maximum Continuous Load Current

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . 27.1 Amps

Phase  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-phase

Rated Frequency  . . . . . . . . . . . . . . . . . . . . . . 60 Hertz

Shipping Weight  . . . . . . . . . . . . . . . . . . . . . . . . 103 lbs.

MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that
all periodic maintenance tasks are completed on a timely
basis; that all discrepancies are corrected; and that the unit
is kept clean and properly stored. NEVER operate a
damaged or defective generator.

Engine Maintenance

See engine owner’s manual for instructions.

CAUTION!

Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has
been shown to cause skin cancer in certain
laboratory animals. Thoroughly wash exposed areas
with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean
and dry. Operate and store the unit in a clean dry
environment where it will not be exposed to excessive
dust, dirt, moisture or any corrosive vapors. Cooling air
slots in the generator must not become clogged with snow,
leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean the generator.
Water can enter engine fuel system and cause problems. In
addition, if water enters generator through cooling air slots,
some of the water will be retained in voids and cracks of the
rotor and stator winding insulation. Water and dirt buildup
on the generator internal windings will eventually decrease
the insulation resistance of these windings.

To Clean the Generator

• Use a damp cloth to wipe exterior surfaces clean.

• Soft, bristle brush may be used to loosen caked on dirt

or oil.

• A vacuum cleaner may be used to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and opening on
generator. These openings must be kept clean and
unobstructed.

STORAGE

The unit should be started at least once every seven days
and allowed to run at least 30 minutes. If this cannot be
done and you must store the unit for more than 30 days,
use the following guidelines to prepare it for storage.

Generator Storage

• Clean the generator as outlined in “To Clean the

Generator” on this page.

• Check that cooling air slots and openings on generator

are open and unobstructed.

CAUTION!

Storage covers can be flammable.

DO NOT place a storage cover over a hot
generator. Let the unit cool for a sufficient time
before placing the cover on the unit.

Engine Storage

See engine owner’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, add fuel stabilizer into fuel
tank and fill with fresh fuel. Run the unit for several
minutes to circulate the additive through the carburetor.
The unit and fuel can then be stored for up to
24 months. Fuel stabilizer can be purchased locally.

• DO NOT store fuel from one season to another unless

it has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it's used with this unit.

• Store unit in a clean and dry area.

Содержание Generac 1653-1

































Отзывы: