background image

5

360

15 meters (50 feet)

OPERATOR SAFETY

WARNING   Thrown debris could cause eye 
injuries. Noise levels could cause hearing 
damage. Nylon trimming line and blades can 
cut through clothes and skin.

•  NEVER operate unit without protective guards in

   place.

•  DO NOT wear loose clothing, jewelry or anything

   that could be caught in the starter or other rotating

   parts.

•  Keep hands and feet away from rotating parts.
•  Wear safety goggles that meet ANSI standards 

   whenever you use the trimmer.

•  Wear hearing protectors.
•  Wear protective clothing to reduce the risk and severity

of injury. Wear trimmer harness, gloves, a long-
sleeved shirt, long pants, and sturdy boots with 
nonslip soles.

         WARNING   Running engine gives off carbon  

        monoxide, an odorless, colorless, poison gas.

        Breathing carbon monoxide can cause headache, 
        fatigue, dizziness, vomiting, confusion, seizures, 
        nausea, fainting or death.
•  Operate equipment ONLY outdoors.
•  Keep exhaust gas from entering a confined area 

   through windows, doors, ventilation intakes, or 
   other openings.

WARNING    Exhaust heat/gases could ignite 
combustibles or structures resulting in death, 
serious injury or property damage. Contact with 
the muffl er area could cause burns resulting in 
serious injury.

•  DO NOT touch hot parts.
•  Allow equipment to cool before touching.
•  It is a violation of California Public Resource Code, 

Section 4442, to use or operate the engine on any 
forest-covered, brush-covered, or grass-covered 
land unless the exhaust system is equipped with a 
spark arrester, as defined in Section 4442, main-
tained in effective working order. Other states or 
jurisdictions may have similar laws. Contact the 
original equipment manufacturer, retailer, or 
dealer to obtain a spark arrester designed for the 
exhaust system installed on the engine.

WARNING    Rapid retraction of starter cord 
(kickback) will pull hand and arm toward engine 
faster than you can let go. Broken bones, 
fractures, bruises, or sprains could result.

•  When starting engine, pull the starter cord slowly 

until resistance is felt and then pull rapidly to avoid 
kickback.

•  Blade or trimmer head must be securely attached.

      WARNING     Improperly maintaining the trimmer, 
or failure to correct a problem before operation, can 
cause a malfunction in which you can be seriously 
hurt or killed. Always follow the inspection and main-
tenance recommendations and schedules in this 
manual.

WARNING     Moving parts could crush and 
cut. Starter and other rotating parts could 
entangle hands, hair, clothing, or accessories 
resulting in serious injury.

•  NEVER operate unit without protective guards in place.
•  DO NOT wear loose clothing, jewelry or anything 

that could be caught in the starter or other rotating 
parts.

•  Tie up long hair.
•  Keep hands and feet away from rotating parts.

WARNING    Objects thrown by the trimmer 
can cause serious injury.

•  Clear the area to be cut before each use. Remove

all objects such as broken glass, nails, wires, or 
string, which could be thrown or become 
entangled in the cutting attachment.

•  Clear the area of children, bystanders, and pets.
•  Keep all children, bystanders outside of a 50 ft (15 m)

radius.

•  Bystanders should be encouraged to wear eye

protection.

WARNING
Unintentional sparking can resul t in fire or electric 
shock.
Unintentionalstart-up can result in entanglement, 
traumatic amputation, or laceration.
Fire hazard.

Before performing adjustments or repairs:
•  Disconnect the spark plug wire and keep it away 

from the spark plug.

•  Use only correct tools.
•  Replacement parts must be of the same design and

installed in the same position as the original parts.

Содержание BP33-W




























Отзывы: