manualshive.com logo in svg

Briggs & Stratton 700 DOV Series, Руководство по ремонту

Поделиться
Скачать
Briggs & Stratton 700 DOV Series Скачать руководство пользователя страница 41

                                                                                                                                                                                       

   37

4

5

Linkage and Spring Orientation

Be sure to note orientation of linkages and 
springs before removing (Figure 5-2).

Figure 5 - 2

Top No-Load RPM

Briggs & Stratton supplies engines with an 
adjustable top no-load RPM, which the 
equipment manufacturers set to their own 
specifications. Do not exceed these limitations.

NOTE:

 Correct top-no-load RPM for each model-

type-trim can be found in the engine replacement 
data on Briggs & Stratton websites.

Top no-load RPM should be checked with a 
tachometer when the engine is operating on a 
completely assembled unit. The equipment 
should be operated under no-load when making 
this check.

If a governor spring must be replaced, consult 
the appropriate Illustrated Parts List for the 
correct part number. After the spring is installed, 
check the top no-load RPM with an accurate 
tachometer, as noted above, and adjust as 
required. (See Section 1 - Safety, Maintenance, 
and Adjustments).

Governor Service

The mechanical governor is part of the oil slinger 
assembly (

A

, Figure 5-1) attached to the sump. 

The governor crank (

B

) is mounted in the 

cylinder assembly.

Disassemble

1. Drain oil from engine into an appropriate 

container.

 2. Remove burrs and clean the crankshaft 

PTO, the carefully remove sump from 
engine and discard the gasket.

 3. Loosen the governor lever nut and slide 

the lever off the governor crank and 
disconnect from the governor link. Set 
aside.

 4. Remove push nut or clip and washer (

C

) 

from governor crank. Remove burrs and 
clean the governor crank, then remove 
crank from inside of cylinder.

NOTE:

 Inspect governor gear for worn weight 

pins and chipped or missing gear teeth before 
removing. Any time the governor gear is 
removed, it must be discarded and replaced with 
a brand new governor gear.

 5. Using two flat screwdrivers, carefully pry 

under governor gear (

D

) to remove from 

spindle. 

 6. Remove cam gear from governor gear to 

remove the spindle.

Inspect Governor Parts

1. Check oil slinger assembly for chipped or 

damaged teeth, or damage on paddles. If 
damage to the oil slinger is found, replace 
the entire sump.

 2. Check governor crank for wear or 

damage. Replace if necessary.

 3. Inspect cam gear for worn or damaged 

teeth and evidence of wear on cam lobe. 
Replace if necessary.

Содержание 700 DOV Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды