background image

18

For Model Series 580447, 583447 & 589447

Which are equal to or more than 19 kW

Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)

and the United States Environmental Protection Agency (U.S. EPA)

Emissions Control System Warranty Statement

(Owner’s Warranty Rights and Obligations)

EMISSIONS CONTROL WARRANTY COVERAGE IS APPLICABLE TO

CERTIFIED MODEL YEAR 2004 AND LATER ENGINES, WHICH ARE

PURCHASED AND USED IN CALIFORNIA, AND TO CERTIFIED MODEL

YEAR 2004 AND LATER ENGINES, WHICH ARE PURCHASED AND

USED ELSEWHERE IN THE UNITED STATES.

California and United States Emissions Control Warranty Statement

The California Air Resources Board (CARB), U.S. EPA and B&S are pleased

to explain the Emissions Control System Warranty on your model year 2004

and later off-road spark-ignition engine over 19kW (25HP). In California, new

off-road large spark-ignition engines must be designed, built and equipped to

meet the State’s stringent anti-smog standards. Elsewhere in the United

States, new Non-road spark-ignition engines over 19kW certified for model

year 2004 and later, must meet similar standards set forth by the U.S. EPA.

B&S must warrant the emissions control system on your engine for the period

of time listed below, provided there has been no abuse, neglect or improper

maintenance of your engine.

Your emissions control system includes parts such as the carburetor, air

cleaner, ignition system, muffler, and catalytic converter. Also included may

be hoses, belts, connectors and other emissions related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost

to you including diagnosis, parts and labor.

Briggs & Stratton Corporation Emissions Control Warranty Coverage

The 2004 and later off-road spark-ignition engines are warranted for two

years.

If any emissions-related part on your engine is defective, the part will be

repaired or replaced by B&S.

Owner’s Warranty Responsibilities

As the engine owner, you are responsible for the performance of the required

maintenance listed in your Operating & Maintenance Instructions. B&S

recommends that you retain all your receipts covering maintenance on your

engine, but B&S cannot deny warranty solely for the lack of receipts or for

your failure to ensure the performance of all scheduled maintenance.

As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect,

improper maintenance or unapproved modifications. You are responsible for

presenting your engine to an Authorized B&S Service Dealer as soon as a

problem exists. The warranty repairs should be completed in a reasonable

amount of time, not to exceed 30 days. If you have questions regarding your

warranty rights and responsibilities, you should contact a B&S Service

Representative at 1-800-233-3723.

EMISSIONS COMPLIANCE PERIOD:

1000 HOURS

Briggs & Stratton Corporation Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control

Warranty Coverage. It is in addition to the B&S engine warranty for

non-regulated engines found in the Operating & Maintenance Instructions.

1.

Warranted Parts

Coverage under this warranty extends only to the parts listed below (the

emissions control systems parts) to the extent these parts were present

on the engine purchased.

a. Fuel Metering System

Carburetor and internal parts

Cold start enrichment system

Fuel pump

Fuel filter

b. Air Induction System

Air cleaner

Intake manifold

c. Ignition System

Spark plug

Ignition coil

Ignition processor

d. Exhaust System

Exhaust manifold

e. Miscellaneous Items Used in Above System

Vacuum, temperature, position, time sensitive valves and switches

Electronic controls

Connectors and assemblies

Hoses

2.

Length of Coverage

B&S warrants to the initial owner and each subsequent purchaser that

the Warranted Parts shall be free from defects in materials and

workmanship which caused the failure of the Warranted Parts for a

period of two years from the date the engine is delivered to a retail

purchaser.

3.

No Charge

Repair or replacement of any Warranted Part will be performed at no

charge to the owner, including diagnostic labor which leads to the

determination that a Warranted Part is defective, if the diagnostic work

is performed at an Authorized B&S Service Dealer. For emissions

warranty service, contact your nearest Authorized B&S Service Dealer

as listed in the “Yellow Pages” under “Engines, Gasoline,” “Gasoline

Engines,” “Lawn Mowers,” or similar category.

4.

Claims and Coverage Exclusions

Warranty claims shall be filed in accordance with the provisions of the

B&S Engine Warranty Policy. Warranty coverage shall be excluded for

failures of Warranted Parts which are not original B&S parts or because

of abuse, neglect or improper maintenance as set forth in the B&S

Engine Warranty Policy. B&S is not liable to cover failures of Warranted

Parts caused by the use of add-on, non-original, or modified parts.

5.

Maintenance

Any Warranted Part which is not scheduled for replacement as required

maintenance or which is scheduled only for regular inspection to the

effect of “repair or replace as necessary” shall be warranted as to

defects for the warranty period. Any Warranted Part which is scheduled

for replacement as required maintenance shall be warranted as to

defects only for the period of time up to the first scheduled replacement

for that part. Any replacement part that is equivalent in performance and

durability may be used in the performance of any maintenance or

repairs. The owner is responsible for the performance of all required

maintenance, as defined in the B&S Operating & Maintenance

Instructions.

6.

Consequential Coverage

Coverage hereunder shall extend to the failure of any engine

components caused by the failure of any Warranted Part still under

warranty.

Содержание 430447





















Отзывы: