Move pressure washer
to safe operating location
1. Move pressure washer outdoors to a flat, level surface.
2. Running engines give off carbon monoxide. Keep at least 5 ft.
(1.5 m) clearance on all sides of pressure washer including overhead
to reduce the risk of exhaust heat or exhaust gases igniting nearby
combustible material.
7
Connect spray gun
NOTICE
Remove and discard the shipping caps from the pump’s high
pressure outlet and water inlet before attaching hoses.
1. Uncoil high-pressure hose (M) and attach one end of hose to base of
spray gun (N). Tighten by hand.
8
2. Attach other end of high-pressure hose (M) to high-pressure outlet
(P) on pump. Tighten by hand.
9
Connect water supply
1.
Inspect garden hose inlet screen (Q) for damage.
10
NOTICE
If inlet screen is damaged or missing, DO NOT use pressure
washer, call
1-800-743-4115
.
2. Clean screen if necessary. Refer to operator’s manual for instructions.
3. Run cold water through garden hose (R) for 30 seconds to clean out
any debris. Garden hose length must not exceed 50 ft. (15 m). Turn
off water supply and attach garden hose to water inlet (S). Tighten by
hand.
10
Start pressure washer
NOTICE
You MUST connect and turn on water supply fully before
starting engine.
1. Put on safety goggles.
2. Turn on water supply.
3. Press the red safety button (T) on the spray gun and squeeze the
trigger (U) to purge the pump system of air and impurities.
11
4. Attach nozzle extension (V) to spray gun (N). Tighten by hand.
12
5. Pull back on collar of nozzle extension (W), insert spray tip (X) and
release collar. Tug on spray tip to make sure it is securely in place.
13
6. Rotate fuel shut-off valve (Y) to ON position.
14
7. Move throttle lever (Z) to FAST (
) position.
15
8. Move choke lever (AA) to CHOKE position.
16
9. When starting engine, position yourself as recommended and grasp
starter grip handle and pull slowly until you feel some resistance.
Then pull rapidly to start engine. After each starting attempt, where
engine fails to run, always point spray gun in a safe direction, push
red button and squeeze spray gun trigger to release retained high
water pressure.
17
10. Return recoil starter slowly. DO NOT let rope “snap back” against
starter.
11. When engine starts, slowly move choke lever (AA) to RUN position,
as engine warms. If engine falters, move choke lever to CHOKE
position, then to RUN position.
16
12. After each starting attempt, where engine fails to run, always point
gun in safe direction, press red safety button and squeeze spray
gun trigger to release high pressure. Move choke lever to CHOKE
position, and repeat steps 9 through 11.
NOTICE
Always keep the throttle lever in the FAST (
) position when
operating the pressure washer.
13. Point gun toward surface to be cleaned. Press the red safety button
and pull trigger to begin spraying.
Stop pressure washer
1. Release spray gun trigger and let engine idle for two minutes.
2. Move throttle lever (Z) to SLOW
(
)
position, then STOP (
)
position.
15
3. Rotate fuel shut-off valve (Y) to OFF position.
14
4. Turn off water supply.
5. Always point spray gun in safe direction, press the red safety
button, and squeeze spray gun trigger to relieve retained high water
pressure.
6. Disconnect garden hose from pump.
7. Disconnect high pressure hose from pump and gun for storage. For
long term storage instructions, see operator’s manual.
8. Remove safety goggles.
You will need:
• Utility knife • Unleaded fuel • Garden hose, 50 ft. (15 m) or less • Safety goggles (indirect vented type)
Items Included:
Operator’s Manual (not shown)
Unpack pressure washer
1. Remove everything from carton except pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly.
If items are damaged or missing, call
1-800-743-4115
.
4. Prior to assembly, lubricate all o-ring connections as described in
operators manual.
Assemble pressure washer
1. Place handle (A) onto handle supports (B) connected to main
unit. Make sure holes (C) in handle align with holes (C) on handle
supports.
1
NOTICE
It may be necessary to move the handle supports from side to
side in order to align the handle so it will slide over the handle supports.
2. Insert carriage bolts (D) through holes from back of unit and attach a
plastic knob (E) from front of unit. Tighten by hand.
2
3. Place accessory tray (F) over holes on handle (G) (viewing from
front of unit). Push tree clips (H) into holes until they sit flat against
accessory tray.
3
4. Insert spray gun holder wireform (J) through hole on left side of
handle (viewing from front of unit). Hold wireform in place and
attach a plastic knob (K) from inside of unit. Tighten by hand.
4
5. Insert multi-colored spray tips in spaces provided in accessory tray.
See
How to Use Accessory Tray,
in operator’s manual.
Add engine oil and fuel
NOTICE
You MUST properly fill engine with oil before attempting to
start pressure washer.
NOTICE
DO NOT use E85 fuel.
NOTICE
DO NOT mix oil with fuel.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove oil fill cap (
).
5
3. Using oil funnel (optional), slowly pour contents of supplied oil into
oil fill opening, frequently checking oil level. DO NOT OVERFILL.
4. Replace oil fill cap and fully tighten.
5. Clean area around the fuel cap (
), remove fuel cap.
5
6. Slowly add regular unleaded fuel to fuel tank. Be careful not
to overfill. Allow about 4 cm (1.5 in.) (L) of tank space for fuel
expansion.
6
7. Install fuel cap and let any spilled fuel evaporate before starting
engine.
WARNING
Failure to read and follow the operator’s
manual and all operating instructions could
result in death, serious injury, and/or property
damage.
WARNING
Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death,
serious injury and/or property damage. Turn
pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Let spilled fuel
evaporate before starting engine. Always allow space for
fuel expansion.
WARNING
Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting
in serious injury. NEVER pull starter cord without first
relieving spray gun pressure. Pull starter cord slowly
until resistance is felt, then pull rapidly. Firmly grasp
spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
WARNING
Running engine gives off carbon
monoxide, an odorless, colorless, poison
gas. Breathing carbon monoxide could result
in death, serious injury, nausea or fainting.
Operate this product ONLY outdoors. DO NOT operate
this product inside any building or enclosure, even if
windows and doors are open.
WARNING
High water pressure could cut through
skin resulting in serious injury. Spray gun
traps high water pressure, even when engine
is stopped and water is disconnected. NEVER
aim spray gun at people, animals, or plants. ALWAYS
point spray gun in safe direction, press red button and
squeeze spray gun trigger to release high pressure,
every time you stop engine.
WARNING
Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas. Breathing carbon
monoxide could result in death, serious injury, nausea or
fainting. Operate this product ONLY outdoors. DO NOT
operate this product inside any building or enclosure, even if windows
and doors are open.
WARNING
Risk of eye injury. Spray could splash back or propel
objects resulting in serious injury. Always wear indirect
vented (chemical splash) safety goggles marked to
comply with ANSI Z87.1 when using or in vicinity of this
equipment. NEVER substitute safety glasses or dry-condition goggles
for indirect vented safety goggles.
WARNING
Starter cord kickback (rapid retraction) will pull hand
and arm toward engine faster than you can let go which
could cause broken bones, fractures, bruises, or sprains
resulting in serious injury. NEVER pull starter cord without
first relieving spray gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Firmly grasp spray gun with both
hands when using high pressure spray to avoid injury when spray gun
kicks back.
Copyright © 2011. All rights reserved. No part of this material may be reproduced or transmitted in any form without the express written permission of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).
1
A
B
C
C
2
D
E
3
G
H
F
4
J
K
17
12
N
V
13
X
W
8
M
N
9
M
P
10
S
R
Q
14
Y
16
AA
15
Z
Quick Setup Guide
3400 MAX PSI* Pressure Washer
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free
1-800-743-4115
or visit our website,
BRIGGSandSTRATTON.com
5
6
L
7
Exhaust Port
Pointed away from
dwelling openings
11
T
U
Not
for
Reproduction
