Brigade Electronics VBV-155, Руководство пользователя

Страница: 2 / 10

INTRODUCTION
This vehicle CCTV system has been designed to provide years of trouble -free
operation. Please read this manual thoroughly. This manual contains
instructions to make the installation of the camera and monitor easier. The
vehicle CCTV system is a supplement to standard rear-view mirror systems, and
will provide additional rear-view vision when installed and maintained properly.
It is not intended in any way to be a substitute for careful and cautious driving.
All applicable traffic laws and motor safety regulations must still be adhered to.
FEATURES
VBV-100C CAMERA
• 290,000 pixel image sensor
Field of view 110° Diag anol
• Auto White Balance (AWB)
• Back Light Compensation (BLC)
• 0.1 Lux sensitivity (18 IR-LED)
• Automatic electronic iris provides a clearer, more consistent
image in low and bright light
• Compact design and lightweight ease installation in most
vehicles.
• Waterproof cable connection (IP67)
• Wind deflector reduces build up of dirt on lens
• CE / e- marking
VBV-155M 5.5" CRT MONITOR
• Brightness/Contrast control
• Two camera inputs and Camera Selector Switch
• Power/stand-by switch
•
• Mirror/Normal selection switchDay/Night Switch
•
• CE / e- marking
CONTENTS OF 1 COMPLETE SYSTEM
VBV-100C CCD CAMERA:
-Camera
-Camera bracket
-Attachment screws with washers
-Wind deflector
VBV-155M MONITOR:
-Monitor
-Snap-on sun visor
-Monitor bracket
-Power harness with locking connector
-Range markers
-Thumb screws
Special cable: 1-20 metre cable with waterproof connector. Oil, gas
grease resistant. UV stable
Documents: 1 – Operations manual
BEFORE INSTALLATION
1. This system operates from 10 volts DC to 32 volts DC, negative
ground.
2. Please install this system according to the instructions in this
manual.
3. Do not disassemble the camera or the monitor. This voids the
warranty. Disassembling th e camera will compromise the
waterproof seal.
4. Connect the system to an ignition switched power source.
Connection to a battery source will reduce battery life.
WARNING
1. To prevent electrical shock, DO NOT OPEN THE MONITOR
CASE. There are potentially lethal voltages inside the monitor.
There are no user serviceable parts inside. If evidence of
tampering is detected, the warranty will be considered void.
2. Keep monitor away from leaking water, rain, moisture etc. It is
NOT waterproof. Any moisture inside the monitor could cause
extensive damage.
3. Use the thumbscrews to mount the monitor to bracket.
4. Do not cover air dusts. Monitor needs proper ventilation to
prevent overheating.
INSTALLATION INSTRUCTIONS
VBV-100C CAMERA
1. Attach camera bracket (see Fig. 1) to upper portion of vehicle.
Attachment point must be sturdy enough to support camera and
bracket.
2. Attach camera to bracket using screws provided. Adjust angle
as indicated in Fig. 2. (Use rear bumper and back of vehicle as a
reference point.)
3. Wind deflector may be installed. This deflector is designed to
reduce the build up of dust, dirt and moisture on the camera lens.
(See Fig.3.)
VBV-155M MONITOR
1. Attach monitor inside vehicle in a location convenient to the
driver (e.g. center of dash, overhead or in dash) (Fig.4.)
2. Use a compression plate to attach the monitor bracket to the
dash or overhead.
3. Adjust mounting angle of the monitor to allow driver to easily
view the screen from all seat positions. (Fig. 5)
CABLE
1. The camera-to-cable connection and the monitor pigtail are
waterpr oof. Be sure to position the cables properly.
2. Do not run the cable over sharp edges or corners. Do not kink
the cable. Keep the cable away from hot and rotating parts.
3. Place all excess cable in convoluted tubing.
4. Wire the cable securely.
WIRING CAMERA AND MONITOR
1. See connection diagram for connections to ignition, ground and
back up circuit. (See Fig. 6.)
2. Wiring camera: Drill a 22mm diameter hole into vehicle body
near the camera and bracket. Connect camera connector to
extension cable in vehicle. Push extra cable into vehicle (be careful
not to kink cable) and fit grommet into hole. Apply sealant around
grommet to increase resistance to water penetration.
3. Wiring Monitor: Insert extension cable into camera #1 position.
If 2 cameras are used, be sure to mark each extension cable
properly and plug second cable into camera #2 position. Bundle
excess cable together using a cable tie or vinyl tape. This will avoid
possible damage to cable during operation.
4. The red wire is connected to an ignition power source, the black
wire is connected to chassis ground, and the brown wire is
connected to the vehicles reverse light circuit.
FUNCTIONS AND OPERATION
MONITOR
1) POWER SWITCH
Press the power switch to turn the monitor on or off.
2) STANDBY LED
When the red LED is turned on, it indicates power on.
When reverse gear is selected the images picked up by camera 1
will be shown on the monitor 3) CONTRAST CONTROL
The contrast can be adjusted to suit settings for “DAY/NIGHT”.4)
BRIGHT CONTROL
The brightness can be adjusted to suit settings for “DAY/NIGHT”. “.
5) CAMERA SELECTOR (CA1)
6) CAMERA SELECTOR (CA2)
Select CA2 to view camera 2
7) NIGHT / DAY SWITCH
8) CAMERA 1
Input connection to camera extension cable.
9) Camera 2
Input connection to additional camera extension cable.
10) VIDEO OUTPUT
Connect video output connector to a second monitor or VCR input
with a RCA phone type connector cable.
11) AUDIO OUTPUT
Connect Audio output connector to a second monitor or VCR input
with a RCA phone type connector cable.
12) EXTERNAL SPEAKER (Optional)
The monitor can be linked to an external speaker 13) MIRROR /
NORMAL SELECTION SWITCH
When the switch is in MIR position, the picture will showreverse
image.
When the switch is in NOR position, the picture will show a normal
image. * Camera 1 & Camera 2 are operated individually.
14) POWER CONNECTION:
PIN 1: Ground - Black
PIN 2: +12/24Vdc ignition - Red
PIN 3: Reverse circuit – Orange
PIN 4: Dimmer - White
CAMERA
Waterproof cable connector (See Fig. 7)
CAUTION
1. DO NOT OPEN THE CAMERA CASE. This will break the
camera’s waterproof seal. If evidence of tampering is detected, the
warranty will be considered void.
2. We do not recommend mounting the camera near the lower
area of the vehicle (e.g. bumper). This reduces the view of the
camera and increases the chance of physical damage to the
camera.
3. Use only the Inner Hexagonal screw and washers to mount the
camera.
MAINTENANCE
Remove dust and dirt with a damp soft cloth. Heavier dirt
should be remo ved with a damp soft cloth and mild detergent.
Do not use strong cleaning agents containing gasoline, thinner,
benzene or alcohol. These substances may damage the
exterior surface of the monitor.
CAUTION
1. Before drilling, be sure no cable or wiring is on the other
side. Be sure to drill a 22mm diameter hole only.
2. Feed as much cable as possible into vehicle and clamp
securely. This reduces the possibility of it being hooked or
snagged.
3. Keep all cables away from HOT, ROTATING and
ELECTRICALLY NOISY components.
4. To increase protection of cable, place all excess wire and
extension cable in convoluted tubing.
5. Do not twist camera cable and do not cut camera pigtail or
cable.
SPECIFICATIONS
VBV-100C CAMERA
VIDEO PICK-UP DEVICE CCD
IMAGE SIZE 1/3 inch
SYNCHRONIZATION INTERNAL
REQUIRED ILLUMINATION 0.1 Lux MINIMUM
VIDEO OUTPUT 1V (p-p), 75 ohm
OPERATING VOLTAGE 12 Vdc
POWER CONSUMPTION MAX 2.4W
(AT 12 Vdc)
RESOLUTION 420 TV LINES
OPERATION TEMP
-20
°
C TO +70
°
C
WEIGHT 0.2Kg
DIMENSION (W x H x D)mm 70
×
44
×
54
VBV-155M MONITOR
VIDEO SYSTEM CCIR
PICTURE TUBE 5.5 INCH PICTURE
PICTURE RESOLUTION 600TV LINES
POWER CONSUMPTION MAX. 1A
OPERATION TEMPERATION -10
°
C TO +50
°
C
OPERATION VOLTAGE DC10 V ~ DC32 V
WEIGHT APPROX. 1.46Kg
DIMENSION (W x H x D)mm 154 x 143 x 190
DISCLAIMER
The use of the VBV-750 Vehicle CCTV system should not in any way be
used as a substitute for careful and cautious driving. Traffic laws and motor
safety regulatio ns must always be adhered to.
BRIGADE ELECTRONICS PLC
TEL: +44 (0) 870 744 1500
FAX: +44 (0) 870 744 1502
Email: sales@brigade-electronics.co.uk
Website: www.brigade-electronics.co.uk
ENGLISH VVBV-155 VEHICLE CCTV SYSTEM